RCCrawler Forums - Tundra-->Sequoia cc-01 build

RCCrawler Forums (http://www.rccrawler.com/forum/)

- Tamiya XC/CC01 (http://www.rccrawler.com/forum/tamiya-xc-cc01/)

- - Tundra-->Sequoia cc-01 build (http://www.rccrawler.com/forum/tamiya-xc-cc01/172630-tundra-sequoia-cc-01-build.html)

Tundra-->Sequoia cc-01 build

Might as well start a thread. more a placeholder for the photos I currently have...slow build as I've started putting time into the Charity Montero Build again.

so this is what I am building.
http://img.photobucket.com/albums/v5...-Sequoia-1.jpg

My plan is to take a Tundra cab and bed, combine them, build a back upper part and make my own SUV. The Sequoia is based on the Tundra running gear so it makes sense to me doing the same at 1:10.

I was expecting to split the cc-01 chassis transversely to stretch the wheel base to the Tundra's but upon further research I found that the Sequoia is not based on the Tundra double cab (tamiya's tundra is a double cab). So I'm going to have to take an inch out of the Tundra to make the sequoia which will leave me near the 10.5" lwb setting of the chassis.

I bought the chassis used, should have kept the new chassis from when I bought the pajero kit, d'oh. Had the chassis lift and clearanced the arms for more articulation up front already done.
I further modified it (as most of you have seen already) by turning the knuckles forward, adding a tie rod and relocating the steering servo into a more traditional over axle chassis mounted setup with a simple drag link to a knuckle.
http://img.photobucket.com/albums/v5...quoia/0007.jpg
http://img.photobucket.com/albums/v5...quoia/0008.jpg
http://img.photobucket.com/albums/v5...quoia/0011.jpg
http://img.photobucket.com/albums/v5...oia/0003-1.jpg

no approach lost
http://img.photobucket.com/albums/v5...oia/0003-2.jpg

Going to run the BFG Thrashes I made (BFG sidewalls, Mud Thrasher treads)
http://img.photobucket.com/albums/v5...shers/0007.jpg

The chassis is just about a runner (short a pinion) so I'll run my spare Range Rover Sport body on it for now.
(earlier picture, no Thrashers)
http://img.photobucket.com/albums/v5...oia/0001-1.jpg

Good tuck too.
http://img.photobucket.com/albums/v5...oia/0003-3.jpg
http://img.photobucket.com/albums/v5...oia/0002-2.jpg
http://img.photobucket.com/albums/v5...oia/0004-2.jpg

will run a Novak 55t in it and possibly add a RC4WD 4:1 gear reduction unit.
has an old school Futaba esc (with built in 30A fuse, lol).
will possibly try making sliders and wheel arch exo for this one.
more later.

Can't wait for this. Looks awesome.

Can't wait. Your fabbing skills are top notch.

That's some great work/thinking. Do you feel like you get better steering?

thanks guys. this should be fun.

Quote:

Originally Posted by Just Zach (Post 1734545)

That's some great work/thinking. Do you feel like you get better steering?

not sure on the steering yet as I'm missing a pinion, preventing me from driving it.
However, just moving the servo horn manually or grabbing the wheels and turning them manually there is minimal slop. there is a bit of bumpsteer on the non-drag linked side but its acceptable to me in exchange for the lack of slop.

check it out for yourself
http://www.youtube.com/watch?v=Bb0CGy0BaEk

and

http://www.youtube.com/watch?v=voHyM...eature=related

http://img.photobucket.com/albums/v5...quoia/0012.jpg

I'll have to check the proportions but it appears I'll have to take 1" or slightly less out of the bed/cab junction and add some of it behind the rear wheel. the rear overhang is longer on the sequoia. If I fake the wheel base a bit (maybe less than 1/8") I can get it to work directly on the cc-01 chassis without adjusting the rear axle location.

http://img.photobucket.com/albums/v5...quoia/0013.jpg

window sills will have to be reworked on rear two windows. rear pillar and rear glass will slope more forward, like the 1:1. The tamiya bed makes the proper transition from the body lines to the bubbled out fender so I'll cut the rear door away at the cab, about 7/8" and mate it with the front of the bed to keep the lines right. Sequoia rear taillight looks like same shape as headlight so I'll look at making the taillights out of headlights.

Can't seem to get the cc-01 chassis working right. problems with the pinion. first the set screw hit the gear when pinion placed in proper location. then got it to work but when I test the chassis outside it dies at first rock, as soon as it has to work against the rock to get the wheels moving up. I'm thinking this is a esc issue. after that it wont work unless I turn it off and on again. then too, the motor stops if I try to turn. am charging the battery again to eliminate that as a reason.

I say just make it a two door wagon. "thumbsup"

i'd hate to nit pick but are you going to move fuel door lol

holy crap this is going to get interesting!

I was wondering how long it would take someone to build one of these. It should be good.

Justin

Yah I was wondering about this too...

Nice build so far man,keep it up!"thumbsup"

Keep posting pics and updates!

Can't wait to see it done.

you come up with the most random variations of the stock bodies. i love it"thumbsup"

True that. I've been a fan for a while.

I'm waiting on his '48 Ford/Supra/Chevy Celebrity Wagon 6-wheel crawler hybrid. :lol:

Just kidding. Although I'd love to see that Jeep Commander crew cab pickup again!

oh man thats funny!
could happen....;-)

Quote:

Originally Posted by Zod Rhombus (Post 1741412)

Although I'd love to see that Jeep Commander crew cab pickup again!

awww, that was my first body...
http://img.photobucket.com/albums/v5...b/IMG_0252.jpg

gave it to someone who is refurbishing it and will give it new life, although I think its on the deep backburner at the moment...

that thing was so cool, and so poorly build, lol...
http://img.photobucket.com/albums/v5...b/IMG_0397.jpg

tonights update:

body cab and bed are mated and first round of rough styrene filling and sanding done. still lots of futzing with this to do.

http://img.photobucket.com/albums/v5...quoia/0014.jpg
http://img.photobucket.com/albums/v5...quoia/0015.jpg
http://img.photobucket.com/albums/v5...quoia/0016.jpg

on the cc-01 chassis (lwb)
http://img.photobucket.com/albums/v5...quoia/0017.jpg

Looking good Pablo"thumbsup" The rear looks like it is missing a little junk in the trunk......:-P

I can smell the glue from here.:lol::lol:

Always like your builds...very creative!"thumbsup"

Pablo are you using Plastruct Bondene to glue the tundra body together? I was just wondering if the solvent would work with the tamiya plastic body and I saw your pics....

thanks guys.

Quote:

Originally Posted by Sasquatchbagger (Post 1745019)

Pablo are you using Plastruct Bondene to glue the tundra body together? I was just wondering if the solvent would work with the tamiya plastic body and I saw your pics....

Usually I use Tenax 7R on styrene and that works fine on the ABS Tamiya bodies, but the Bondene works better between the styrene and ABS. it works really well on the tamiya bodies.