| |
10-14-2012, 06:23 AM
| #1 |
| Pebble Pounder Join Date: Jul 2007 Location: deva - romania
Posts: 154
|  JunFac shaft for CC-01
What is the lenght of the JunFac shaft that you are installed on your rigs? I intend to collect some data for the various wheel base, what lenght for Jeep/Pajero, Bronco and Toyota ? |
|  |
| Sponsored Links | |
| | |
|
10-14-2012, 04:08 PM
| #2 |
| Rock Crawler Join Date: Jul 2012 Location: Brisbane, Australia
Posts: 571
| Re: JunFac shaft for CC-01
Am I missing the point here? JunFac make a shaft specifically for the CC-01 and all CC-01s are the same in terms of driveshaft length.
|
|
| |
|
10-14-2012, 09:11 PM
| #3 |
| Newbie Join Date: Nov 2005 Location: Somewhere
Posts: 38
| Re: JunFac shaft for CC-01
The Honda CR-V and Touareg are the only ones that use longer driveshafts. All the others should use the shorter version.
|
|
| |
|
10-14-2012, 09:17 PM
| #4 |
| Rock Crawler Join Date: Jul 2012 Location: Brisbane, Australia
Posts: 571
| Re: JunFac shaft for CC-01 Hardened Universal Shaft (107-142mm) 5mm hole [J90033] : JunFac.com That is the same size in all dimensions as the shaft that is sold specifically for the CC01. However, if you want more length, go for Hardened Universal Shaft (120-155mm) 5mm hole [J90034] : JunFac.com. I have that second one in my CC01 now after having the 'made for CC01' unit in and it's much better. Much more shaft up inside the other one, no way it could come apart on a CC01. I've only had two because I lost half of the first one and went to the local hobby shop instead of waiting for JunFac. |
|
| |
|
10-14-2012, 10:05 PM
| #5 |
| Pebble Pounder Join Date: Jul 2007 Location: deva - romania
Posts: 154
| Re: JunFac shaft for CC-01
...as I know the Jeep and Pajero are the short wheelbase versions, the Touareg is the long version and the Bronco and Cruiser use intermediate wheelbase lenght...and I see people who get JunFac 4 link upgrade, are using different shafts...
|
|
| |
|
10-14-2012, 10:10 PM
| #6 |
| Rock Crawler Join Date: Jul 2012 Location: Brisbane, Australia
Posts: 571
| Re: JunFac shaft for CC-01
I ran the stock shaft on my Landcruiser CC01 with the JunFac 4-link kit. Was just long enough to not be pulling on the axle pinion input. Like 1mm of play at full droop.
|
|
| |
|
10-15-2012, 02:39 AM
| #7 |
| Pebble Pounder Join Date: Jul 2007 Location: deva - romania
Posts: 154
| Re: JunFac shaft for CC-01
Thanks...can I have a pics of you fully extended and compressed?...Thanks a lot and sorry for my noobs questions.
|
|
| |
|
10-15-2012, 03:59 AM
| #8 |
| Rock Crawler Join Date: Jul 2012 Location: Brisbane, Australia
Posts: 571
| Re: JunFac shaft for CC-01
My chassis is over at MoonUnit's place at the moment. I'll try and get some pics this week.
|
|
| |
|
10-15-2012, 06:16 AM
| #9 |
| Pebble Pounder Join Date: Jul 2007 Location: deva - romania
Posts: 154
| Re: JunFac shaft for CC-01
thanks...
|
|
| |
|
03-07-2013, 11:58 AM
| #10 |
| Newbie Join Date: Dec 2012 Location: Denver
Posts: 26
|
I'm a little confused on what shaft I can out in my Toaureg CC01. This site says something different then what the thread says. http://www.rcplanet.com/Junfac_Harde...p/jun90034.htm Any help would b great!! Sent from my iPhone 5 using Tapatalk |
|
| |
|
03-07-2013, 05:03 PM
| #11 |
| Rock Crawler Join Date: Jul 2012 Location: Brisbane, Australia
Posts: 571
| Re: JunFac shaft for CC-01
It should be the 107-142mm version, but a little shorter wont hurt you.
|
|
| |
|
03-07-2013, 05:11 PM
| #12 |
| Newbie Join Date: Dec 2012 Location: Denver
Posts: 26
|
That helps. Thx! Sent from my iPhone 5 using Tapatalk |
|
| |
|
10-19-2013, 05:51 PM
| #13 |
| Newbie Join Date: Jan 2005 Location: Bradenton
Posts: 36
| Re: JunFac shaft for CC-01 |
|
| |
 |
JunFac shaft for CC-01 - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Junfac Universal Shaft | Tedro | Axial SCX-10 | 10 | 09-18-2010 12:35 PM |
| junfac drive shaft | LEROY | Axial SCX-10 | 11 | 09-11-2010 02:39 AM |
| Junfac drive shaft.... | HRDROKN | Venom Creeper | 15 | 01-21-2010 12:36 PM |
| JunFac Universal Shaft | AlphaDOG | Axial AX-10 Scorpion | 14 | 09-26-2009 12:08 AM |
| new shaft from JunFac | vcar1 | Tamiya CR-01 | 25 | 02-10-2009 09:06 AM |
| |
Linear Mode
