|
| LinkBack | Thread Tools | Display Modes |
07-14-2019, 05:28 AM | #1 |
Newbie Join Date: Jul 2019 Location: China
Posts: 29
| Level 1 Belt Drive Reduction Unit for CC01(with .stl files sharing link)
//----------------2019-10-09 Found a big problem...---------------- I'm so sorry that I just found a big problem to my belt drive GRU: I set the bearing holes to 10.8mm, which is slightly smaller than the bearing(11.0mm in diameter),so that the bearings can be tight fit to the printed parts, and this design worked okay with HP MJF nylon. However, when I tried SLS nylon for my GRU recently, I found the 10.8mm bearing holes are too narrow for 1150 bearings, there's no way to install them. I'm so sorry for this careless mistake, and I'll try to fix it as soon as possible... //--------------2019-10-09 Found a big problem...---------------- The OneDrive sharing link: //--------------------------------------------------------// https://1drv.ms/f/s!AqdwteuJVzvUiFkAXgd2ExtZ4nuq //--------------------------------------------------------// This gear reduction unit contains two pieces of 3D print parts: This unit is installed to my CC01 chassis: //--------------------------------------------------------// Build a crawler type CC01 using 3D print parts //--------------------------------------------------------// ATTENTION: 1. This unit is designed by me, but I don't own a 3D printer---I ordered the parts to an Internet 3D print factory, they produced the parts in goog quality. But I don't know what would turn out if they were printed elsewhere, even they all simple shaped parts. 2.The Part-A is a part which directly contact to the motor---Consider that the motor could be very hot(50~60 degree when climbing a long, tough trail, I believe), I chose nylon to print them, in case the heat of the motor could make SLA resin deform and ruin the unit. Personally I would recommend SLS or MJF nylon. 3. To install this unit to a CC01 chassis, you'll need some 2GT(or GT2) type belt drive parts, two ball bearings, and a 5mm steel shaft. Additionally, a pinion gear with 5mm bore to fit the shaft. Here's the detail: Last edited by ShouryLiu; 10-09-2019 at 06:02 AM. |
Sponsored Links | |
07-14-2019, 05:36 AM | #2 |
Newbie Join Date: Jul 2019 Location: China
Posts: 29
| Re: Level 1 Belt Drive Reduction Unit for CC01(with .stl files sharing link)
More discription will be done, but I'm a little busy right now...so let me finish this thread later...
|
10-06-2019, 08:56 AM | #3 |
I wanna be Dave Join Date: Aug 2004 Location: central VT
Posts: 2,300
| Re: Level 1 Belt Drive Reduction Unit for CC01(with .stl files sharing link)
I'm intrigued. I am having difficulty picturing it installed though. Can't wait to see your project completed. What kind of ratio does this offer? Can you adjust it by pulley size? |
10-06-2019, 11:41 AM | #4 |
I wanna be Dave Join Date: Jun 2017 Location: Humboldt county
Posts: 4,475
| Re: Level 1 Belt Drive Reduction Unit for CC01(with .stl files sharing link)
Pictures are in the build thread linked in the first post (2nd post) Build a crawler type CC01 using 3D print parts Thanks for sharing your designs Shouryliu I would guess that changing pulley sizes should be possible, so long as you can find a belt that fits and theres physically the space for it. |
10-09-2019, 06:20 AM | #5 | |
Newbie Join Date: Jul 2019 Location: China
Posts: 29
| Re: Level 1 Belt Drive Reduction Unit for CC01(with .stl files sharing link) Quote:
If use a combination of 16t/30t pulley, the final ratio would be 22, also a good choice I believe. | |
10-09-2019, 06:30 AM | #6 | |
Newbie Join Date: Jul 2019 Location: China
Posts: 29
| Re: Level 1 Belt Drive Reduction Unit for CC01(with .stl files sharing link) Quote:
I just found the bearing hole diameter I set in my .stl file may not suitable for SLS nylon, hope this mistake didn't waste your time and money... Yes it is free to use different size of pulley in this unit, but it may take several tries to find the right length of belt | |
Level 1 Belt Drive Reduction Unit for CC01(with .stl files sharing link) - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Looking for old GamyRC STL files, for losi/sumo/rocksta etc.. | R3DRumG33k | Micro Scale Rigs | 7 | 01-24-2019 09:52 AM |
Belt Drive | monkeyracing | Axial SCX-10 | 22 | 08-06-2017 11:42 PM |
3D printed body STL files? | raybies_AU | Paint and Body | 3 | 07-27-2017 05:42 PM |
CAD Files (DWG, DXF, STL, IGES, VDA, VRML) | BARK | General Crawlers | 23 | 12-24-2010 07:23 PM |
Thread Tools | |
Display Modes | |
| |