05-02-2021, 09:19 PM | #1 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| I need help
Can some one please tell me, the size of the E-Clips needed for the pins for the lower aluminum a arms for the CC01 ??, I waited over a month, for the a arms to come from China and they then shorted me 3 or 4 E-clips, I have no way to measure the diameter of pins or due you measure the diameter of groove of e-clip for the pins ??, the seller is not replying to me on Ebay where I ordered them, I will buy extra's if I can figure out the size of the clips
Last edited by kgb424; 05-02-2021 at 09:22 PM. |
Sponsored Links | |
05-02-2021, 09:32 PM | #2 |
Rock Crawler Join Date: Mar 2021 Location: Santa Barbara
Posts: 659
| Re: I need help
I would just order this, and hope for the best... https://www.amazon.com/dp/B08N9G8ZMJ...ing=UTF8&psc=1 |
05-03-2021, 06:34 AM | #3 |
I wanna be Dave Join Date: Sep 2011 Location: Douglassville, PA
Posts: 4,224
| Re: I need help
It's a 4mm shaft, so I assume 4mm e-clips would work.
|
05-03-2021, 02:19 PM | #4 |
Quarry Creeper Join Date: Dec 2016 Location: Cawston, British Columbia, Canada
Posts: 478
| Re: I need help
If the shaft is 4mm outside diameter, the clip size should be 3.2mm. 3.2mm is 0.125 inches so a 1/8 inch e-clip might work as well. Can't guarantee that though. |
05-03-2021, 10:02 PM | #5 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: I need help
Thanks everybody for responding, I'm going to go with DRED805 suggestion and buy one of the kits, cause I also can use them on my Weber carb on Yoter, I lost one or two, the last time I rebuilt the carb and used my extra clips from Tamiya kits I built but don't have anymore, and have bought the bigger sized ones at Napa, so that also saves me a trip into town too if I have a kit
Last edited by kgb424; 05-03-2021 at 10:08 PM. |
05-13-2021, 07:13 PM | #6 |
I wanna be Dave Join Date: Mar 2013 Location: Minden
Posts: 2,198
| Re: I need help
I got the E-clips kits, just have not had the time until right, and it confirms that I need reading glasses, cause I had my eyes tested and its hard to see small print and the e-clips were a pain in the ass, I could not see the grove to start the clip in position on the pin, but I got it done, and will go look at frames and get the Blue Light Blocking Coating, so I can also use them when gaming or online, I spend a lot of hours on my Desktop, and they will help my eyes and will be able see shit up close to build RC's, being struggling now I know why
Last edited by kgb424; 05-13-2021 at 07:19 PM. |
05-19-2021, 10:49 AM | #7 |
Rock Stacker Join Date: Jul 2020 Location: Silver Spring
Posts: 59
| Re: I need help
Just started needing readers so I feel your pain. I am still on store bought options which can be tough because apparently I have a wide head. I have also been using my phone for magnification and think it is finally time to purchase an eclip remover installer as the last project was pretty brutal when you add reduced vision to it.
|
| |