Go Back   RCCrawler Forums > RCCrawler Brand Specific Tech > Team Losi Comp Crawler
Loading

Notices

Thread: Where do I go from here?

Reply
 
LinkBack Thread Tools Display Modes
Old 03-04-2019, 08:35 PM   #141
ROCK STOP HOBBIES
 
CM9000's Avatar
 
Join Date: Feb 2009
Location: Detroit
Posts: 1,814
Default Re: Where do I go from here?

Hey bud, are you using stock length links? The losi night crawler shafts will work on any losi cc or nc. You can also use losi 22 series cvd's with the nc cups. but they are shorter. I think there are 3-5 different 22 series shafts out now.

If you have tapatalk on your phone you can post pictures for free, but its always good to support the site and pay for the subscription too.

If you need help with anything losi cc or nc related, I can help you out if the searching doesn't work well.
CM9000 is online now   Reply With Quote
Sponsored Links
Old 03-04-2019, 09:13 PM   #142
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Quote:
Originally Posted by CM9000 View Post
Hey bud, are you using stock length links? The losi night crawler shafts will work on any losi cc or nc. You can also use losi 22 series cvd's with the nc cups. but they are shorter. I think there are 3-5 different 22 series shafts out now.

If you have tapatalk on your phone you can post pictures for free, but its always good to support the site and pay for the subscription too.

If you need help with anything losi cc or nc related, I can help you out if the searching doesn't work well.
Iím using vanquish Ti rods I donít remember the lengths. I believe I posted them in the show us your Losi thread. They arenít exact but they are close to stock end to end. I had an issue with breaking the LNC shafts so I wanted to upgrade since then. I got them this morning but I canít post up pix till later on this week. The ones I bought are 109mm to 135 mm and the are small dia. from hot racing
Rattzo1 is offline   Reply With Quote
Old 03-04-2019, 09:32 PM   #143
ROCK STOP HOBBIES
 
CM9000's Avatar
 
Join Date: Feb 2009
Location: Detroit
Posts: 1,814
Default Re: Where do I go from here?

Ah, gotcha. I havent broke a stock lnc shaft yet. We will see when i go to NENC. Lol.

Sent from my LGMP260 using Tapatalk
CM9000 is online now   Reply With Quote
Old 03-09-2019, 10:18 AM   #144
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Received my 25t spool today and I am in the process of picking up the last few things I need to anodize most everything. Iíll start posting up pix when I get it all ready to assemble. I know some of you Losi guys ainít going to like this , but Iím thinking about ar axles or a set of dlux berg moa axles.not sure if Iíll do it on this or maybe build my hustler super
Rattzo1 is offline   Reply With Quote
Old 03-11-2019, 03:24 PM   #145
ROCK STOP HOBBIES
 
CM9000's Avatar
 
Join Date: Feb 2009
Location: Detroit
Posts: 1,814
Default Re: Where do I go from here?

hustler super with DLUX flavor.
CM9000 is online now   Reply With Quote
Old 03-14-2019, 03:48 PM   #146
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Quote:
Originally Posted by CM9000 View Post
hustler super with DLUX flavor.
Ya that sounds good
Rattzo1 is offline   Reply With Quote
Old 03-17-2019, 09:22 AM   #147
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Got my new power supply DELL poweredge 6800 kd175 server psu for 30$ eBay. I got it up and running last night . So now I have the correct power to do my anodizing and once I’m done with that they make really good battery chargers from what I’m reading . So I’ll be gettin to posting pics soon
Rattzo1 is offline   Reply With Quote
Old 04-17-2019, 01:20 PM   #148
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Ordered a set of Berg v1 axles for her. Has a few issues at home so had to put things on hold . I’ve got that all taken care of now back to my little girl. Going front steer for now I am adding rear steer after while. And I’ll have most my stuff anodized this weekend. Edited this this morning from bully II to berg axles , I had a last minute mind change after being up all night looking through dlux’s Web site and seeing all the goodies for the bergs and nothing much for the bullys. So there’s that I guess lol

Last edited by Rattzo1; 04-18-2019 at 02:17 AM.
Rattzo1 is offline   Reply With Quote
Old 04-18-2019, 06:27 AM   #149
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

I almost forgot , I ordered a topper kit from DMG too I should have everything by sat . Hope I get everything anodized I would like to run this be-auch again lol
Rattzo1 is offline   Reply With Quote
Old 04-20-2019, 09:30 AM   #150
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Box-o-Goodies
Attached Images
 
Rattzo1 is offline   Reply With Quote
Old 04-21-2019, 06:04 PM   #151
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

I won my second motor today Novak ballistic 17.5 to make the set. Been trying to find the class rules for 2.2 sport , b4 I make my links . IDE like to make it legal and stuff . Going to try them on the losi chassis see how I like them if I donít Iím getting Dlux chassis and links. Thatís for a different thread though. I also thought about making the hustler a super droop with the new losi center section. IDE hate to waist all the losi crap Iíve bought up over the past year. Lol. Iíve got nothing anodized yet I forgot how bad the prep work suck ! So thatís what Iíve been doing ( stripping, cleaning , scrubbing and will probably polish or fine fine sand paper it then clean it again .) then itís ready I have so much to do if I use the losi axles lol . If not just wheels rings chassis and thatís about it unless I make aluminum rods . So lots to do ttyl
Rattzo1 is offline   Reply With Quote
Old 04-21-2019, 07:52 PM   #152
Tib
Pebble Pounder
 
Join Date: Mar 2016
Location: Harrisburg/York
Posts: 110
Default Re: Where do I go from here?

Quote:
Originally Posted by Rattzo1 View Post
Box-o-Goodies


So nice


Sent from my iPhone using Tapatalk
Tib is offline   Reply With Quote
Old 05-09-2019, 11:59 AM   #153
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Did some soul searching and decided that I wasnít going to waist these axles under a LNC so Iím sidebaring the moa for now and focusing on a unstuck sporty . So I Made another order this morning, well two orders one from krazed for the losi unstuck gen 2 and one from Dlux for the lower links and a set of his xr length FBA axles . Iím going to try and modify the tang to fit the losi locker. I think they have enough meat on them to be able to file the sides and make it square. And if not Iíll keep them for my Berg rear axle .i almost got everything ready to anodize I should be doing that all weekend going to do two different colors. Black and I think orange maybe red we will see.
Rattzo1 is offline   Reply With Quote
Old 05-18-2019, 12:00 PM   #154
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Well I got all the parts sanded and ready to anodized and my unstuck showed up . I'm not real crazy about the 3d printed stuff it's nice but I don't like the look of it , so I'm sanding and polishing that stuff and I'm waiting for my bank to send me a new bank card so I can pay Erik from Dlux to make my upper links and send that stuff to me so I'll be a while building it yet I guess . But here is a pic of each. Thanx for lookin
Attached Images
  
Rattzo1 is offline   Reply With Quote
Old 05-18-2019, 12:03 PM   #155
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Sorry I didn't realize it was that blurry of a pic. I'll take better with my phone later
Rattzo1 is offline   Reply With Quote
Old 05-19-2019, 01:48 PM   #156
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

So here I am waiting , got the rest of my stuff sanded made my titanium link pins and got the printed chassis stuff sanded. My bank is killing me they were supposed to get it out to me by Friday . That didnít happen so now I guess Iím waiting another week for Dlux to send my links and axles.i know Iím nowhere near close to assembling it but I really hate waiting !
Attached Images
  
Rattzo1 is offline   Reply With Quote
Old 05-19-2019, 05:46 PM   #157
Rock Stacker
 
Join Date: Jan 2017
Location: Bakersfield
Posts: 81
Default Re: Where do I go from here?

Looking good. The printed parts definitely look way better sanded.


Live it love it crawl it
tjsnyder is offline   Reply With Quote
Old 05-19-2019, 08:04 PM   #158
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

Looking good. The printed parts definitely look way better sanded.

Thank you !, I definitely agree, they still arnt perfect but don’t look as cheap. If that makes any sense. I’ve also got my colors for anodizing narrowed down to , Black/ Orange or Purple /Green or Teal

Last edited by Rattzo1; 05-19-2019 at 08:11 PM.
Rattzo1 is offline   Reply With Quote
Old 05-22-2019, 09:52 AM   #159
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

So With this chassis I need 3.5” shocks and I’ve been looking at the dravetech shocks that Dlux has on his site. Then I happened to pull out my old CEN nitro buggy and it just so happens to have 3.5” shocks. Not only that but they have a skinny spot at the bottom of the body where the packing goes , and that skinny step is just a hair bigger than my little springs that are for my desert lizard shocks. So I’m going to try and make my own that look like the dravetech I’ll take a couple pix at lunch time. Ok now looking at the pics I see that I have a pile of work to do on them yet so I may buy a set of dravetech and finish these for another project.
Attached Images
   

Last edited by Rattzo1; 05-22-2019 at 10:54 AM.
Rattzo1 is offline   Reply With Quote
Old 05-23-2019, 11:07 AM   #160
Quarry Creeper
 
Join Date: Jan 2018
Location: East brady
Posts: 205
Default Re: Where do I go from here?

So this is what they will look like b4 the anodizing. I am still undecided on a color but Iím down to 3, Aquamarine, plum purple or neon green. The plum is a little dark but I think I can add orange to it and lighten it up. The Aqua and Green are nice but I really never liked Green lol. Anyways soon as I figure that out Iíll be gtg.
Attached Images
 
Rattzo1 is offline   Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 02:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com