Drill press rim mod's with VP hubs Alot of people have ask me about this mod so i thought i would do a quick how to hope this help. Frist take a wide hex and a vp hub bolt it to a 1.9 rim. http://i609.photobucket.com/albums/t...g?t=1292350876 http://i609.photobucket.com/albums/t...g?t=1292350911 http://i609.photobucket.com/albums/t...g?t=1292350936 Then take a 5/32 drill bet using the hub as your guide, after that take the hub off then redrill the holes using a 1/8 drill bet. http://i609.photobucket.com/albums/t...g?t=1292350999 Then using a 13/32 drill to open up the center hole to fet your wheel wrench. http://i609.photobucket.com/albums/t...g?t=1292351036 Then you have two ways you can bolt up ether put the bolt throw the rims then add nut for that stock look or bolt them up as normal i hope this help, http://i609.photobucket.com/albums/t...g?t=1292351250 |
re: Drill press rim mod's with VP hubs Nice job there. Cool idea for sure "thumbsup" |
re: Drill press rim mod's with VP hubs Quote:
|
re: Drill press rim mod's with VP hubs So this do you still use the cross pin yet. |
re: Drill press rim mod's with VP hubs Quote:
http://i609.photobucket.com/albums/t...g?t=1324494100 |
re: Drill press rim mod's with VP hubs Got it now. So what size are them hubs bye chance. |
re: Drill press rim mod's with VP hubs Quote:
|
re: Drill press rim mod's with VP hubs You can also adjust the width with the SLW Half Spacers from Rob B. @ CDW."thumbsup" Shamless Plug:ror: |
re: Drill press rim mod's with VP hubs Quote:
This great new for breathing new life into these wheels. |
re: Drill press rim mod's with VP hubs The same principle applies to other wheels too."thumbsup" |
re: Drill press rim mod's with VP hubs Very cool! I wish I hadn't sold off those brand new 1.9's now :ror: |
re: Drill press rim mod's with VP hubs Did you shave hex down or leave it ? This great new for breathing new life into these wheels. Just leave it as is:mrgreen: |
re: Drill press rim mod's with VP hubs I had a spare wheel to try out. Decided to get it shot. I used 4-40 drill & tap set. I threaded the holes for 4-40. http://i850.photobucket.com/albums/a...3/IMAG0492.jpg http://i850.photobucket.com/albums/a...3/IMAG0493.jpg http://i850.photobucket.com/albums/a...3/IMAG0495.jpg http://i850.photobucket.com/albums/a...3/IMAG0496.jpg This good mod for me since I have run 8mm wide hex to clear my TSS,MSD wheels. But with the axial's I can run normal width hex. It looks like I could run SCX10 narrow hex now. Awesome mod for sure! "thumbsup" |
re: Drill press rim mod's with VP hubs Very cool looken, anyone who has done this mod let's see your pic's"thumbsup" |
re: Drill press rim mod's with VP hubs very cool mod thanks for sharing |
re: Drill press rim mod's with VP hubs Quote:
What kind of knuckle weights do you have there? |
re: Drill press rim mod's with VP hubs Quote:
|
re: Drill press rim mod's with VP hubs I have some other wheel mods how to;s i'll post up soon,if there a wheel mod you would like to see just post up and i;ll see what i can do "thumbsup" |
re: Drill press rim mod's with VP hubs I have some other wheel mods how to;s i'll post up soon,if there a wheel mod you would like to see just post up and i;ll see what i can do "thumbsup" |
re: Drill press rim mod's with VP hubs I really like this idea. I might be needing a wider stance for a build I'm doing. Do you think this would be better/stronger than the rc4wd wideners? I would think so, but I haven't used either. Thanks for the how to! |
re: Drill press rim mod's with VP hubs Quote:
|
re: Drill press rim mod's with VP hubs How do the numbers that represent the hubs transfer to width? What I mean is; if a hub is a 225, then is it actually 1/4 inch wide? thanks! Also, does anyone know if the VP hubs wil bolt up to the OEM steel wheels? |
re: Drill press rim mod's with VP hubs Quote:
|
re: Drill press rim mod's with VP hubs thanks bud |
re: Drill press rim mod's with VP hubs Quote:
350=3\8 475=1\2 600=5\8 |
re: Drill press rim mod's with VP hubs This is too cool, great idea"thumbsup" This will come in handy, when I build another toyota:ror: thanks |
re: Drill press rim mod's with VP hubs you have any pics of the back of the rim after drilling? looks like to me that the holes would be half on the flat side and half down the edge of the wheel. seems like it would split the wheel. |
re: Drill press rim mod's with VP hubs Great writeup Mr V. "thumbsup" I know I was one of the ones who asked you about them. Thanks for posting this up. This mod adds realism and function! |
re: Drill press rim mod's with VP hubs Quote:
http://i609.photobucket.com/albums/t...g?t=1327171415 http://i609.photobucket.com/albums/t...g?t=1327171383 |
re: Drill press rim mod's with VP hubs I ran this mod thur scale comp and 2 gtg on 8lbs scaler on 4s. They been holding up great. This been another awesome mod! Thank you MR. V. "thumbsup" |
re: Drill press rim mod's with VP hubs hey thanks for the pics. i was looking at my stock 2.2 axial beadlocks and with my vp hubs it looked like i would have to drill half in and half out of the flat spot by the hex. i guess that's whats gotta be done. now time to go find somebody with a drill press i can use! |
re: Drill press rim mod's with VP hubs I will get a pair 2.2 axial rim and do the mod to them on monday,then post some how to pics. |
re: Drill press rim mod's with VP hubs I feel like trying this because I don't like the look of most steelies, but this mod looks great, and I like the wheel design anyway |
re: Drill press rim mod's with VP hubs I have 2.2 proline 8 shooters and one hexs is starting to wear and I remembered this thread. You think this would work as the back face isnt flat. I checked out my axial 8 holes and the back side looks the same. http://i199.photobucket.com/albums/a...k/IMAG0391.jpg Nik |
re: Drill press rim mod's with VP hubs Yes this mod will work on most rims "thumbsup" |
re: Drill press rim mod's with VP hubs Great idea and thanks for posting the how to and pics! |
re: Drill press rim mod's with VP hubs So how many of you have done the mod would like to see some pics and some new idea "thumbsup" |
re: Drill press rim mod's with VP hubs For those of you who like running plastic rim on your comp crawler here one for you. http://i609.photobucket.com/albums/t...g?t=1331145160 http://i609.photobucket.com/albums/t...g?t=1331145200 |
re: Drill press rim mod's with VP hubs I tried this on my truggy and it worked out great Thanks Mr. Vertical "thumbsup" http://i179.photobucket.com/albums/w...plkmnbnhjk.jpg http://i179.photobucket.com/albums/w...xnbfde3fgc.jpg http://i179.photobucket.com/albums/w...kjbghuhhjm.jpg http://i179.photobucket.com/albums/w...1ag/mmkmkl.jpg |
re: Drill press rim mod's with VP hubs The one thing i like is that it bring new life to old rims. P.S those look great glad it work for you. |
All times are GMT -6. The time now is 10:37 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com