|
| LinkBack | Thread Tools | Display Modes |
09-04-2019, 06:46 PM | #1 |
Rock Crawler Join Date: Jan 2013 Location: San Diego
Posts: 605
| Gearhead/Locked Up 8-Lug Compatibility
Does anybody know if the AO8 flanges are the same bolt pattern as the Gearhead 1.55 UTE wheels, which also use an 8 bolt hub? The UTE wheels sit a little too far out for my current build, and I can't find any other hub offerings from Gearhead. I am hoping to use the LURC 285 AO8 flange hub to cut down the offset a bit. |
Sponsored Links | |
09-04-2019, 07:10 PM | #2 |
I wanna be Dave Join Date: Jun 2017 Location: Humboldt county
Posts: 4,482
| Re: Gearhead/Locked Up 8-Lug Compatibility
I dont know the answer to that but I can measure the 1.9 UTE wheels I have (you'll need to check with RPP or Gearhead if they use the same hub and screws as the 1.5). Then you can ask LURC what their hole spacing is. This again is the 1.9 version, these measurements seemed pretty spot on though when I took the pictures the calipers moved some so it may look a bit off. |
09-04-2019, 07:44 PM | #3 |
Rock Crawler Join Date: Jan 2013 Location: San Diego
Posts: 605
| Re: Gearhead/Locked Up 8-Lug Compatibility
Thanks HumboldtEF! As far as I can tell, the 1.9 and 1.55 hubs are the same; at minimum, they do use the same 8-lug spacers so they should be the same. I'll message Locked Up and see if they can throw a few dimensions my way.
|
09-04-2019, 07:53 PM | #4 |
I wanna be Dave Join Date: Jun 2017 Location: Humboldt county
Posts: 4,482
| Re: Gearhead/Locked Up 8-Lug Compatibility
yeah I just looked at some pictures of each and they look like they may be the same.
Last edited by HumboldtEF; 09-04-2019 at 08:06 PM. |
09-04-2019, 11:39 PM | #5 |
I wanna be Dave Join Date: Oct 2010 Location: Caldwell ID.
Posts: 4,328
| Re: Gearhead/Locked Up 8-Lug Compatibility
I have the 8lug A08 from locked up. I will measure it out in the morning.
|
09-05-2019, 07:05 AM | #6 |
Quarry Creeper Join Date: Jul 2013 Location: PA
Posts: 320
| Re: Gearhead/Locked Up 8-Lug Compatibility
I have both. AO8 and gearheads are different. This is specifically for 1.55.. LURC is much more scale sized...
|
09-05-2019, 10:36 AM | #7 |
I wanna be Dave Join Date: Oct 2010 Location: Caldwell ID.
Posts: 4,328
| Re: Gearhead/Locked Up 8-Lug Compatibility
14mm lug pattern 4mm between lugs. Much smaller than the shown gearheads.
|
09-05-2019, 09:28 PM | #8 |
Rock Crawler Join Date: Jan 2013 Location: San Diego
Posts: 605
| Re: Gearhead/Locked Up 8-Lug Compatibility
Thanks Lonelycreeper! Looks like I'll have to try and get some custom made then...
|
Gearhead/Locked Up 8-Lug Compatibility - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Locked Up RC - New 2.2 wheel options with wheel lug patterns | Locked Up | Locked Up RC | 4 | 07-23-2012 07:00 PM |
Axial AX10 Locked Axle Set and Locked Transmission | Xtant3150c | General Crawlers | 13 | 07-22-2007 01:39 PM |
| |