RCCrawler Forums

andres-tavares · 10-30-2007, 04:49 PM

hi i want to give a mashers 2000 looks to my tlt stock tires

how can i do that??

thanks

RCholic · 10-31-2007, 06:02 AM

I too has wondering how guys "cut or grind" the tire tread...
more so what tools they use?

I tried searching but am not find the right wording... everything comes up for making tires out of 2 different sets.

OldNube · 10-31-2007, 06:18 AM

I tried a dremel...............messy
I tried a hobby knife.......painful
Now I'm looking for some kind of end for my soldering iron that might work. Some kind of loop so you could pick (melt / cut) off individual lugs.

SeanD · 10-31-2007, 06:51 AM

While the Dremel may be messy, its probably the quickest, safest and neatest. I took the Dremel to my stock Wheely King tires.

First I used three cutoff wheels stacked together to cut channels in the lugs. These wheels eat away the rubber pretty quick and with good control. It does kick up a lot of rubber dust so make sure you are wearing a mask.

Once I had the lugs cut down, I used a small sanding drum (again on the Dremel) to thin out the tire carcass and to do general clean up around the areas cut by the cutoff wheels.

They ended up looking like this:

As for the mess, the rubber dust looks dirty but it actually just brushes off and leaves no stain or permanent mark. If you do this outside or in a work area, the cleanup is pretty easy. The big thing is protect your mouth/nose/eyes - just like you would when working with a Dremel anyway.

As for burning the lugs, I take the rubber dust anyday to the most-likely toxic fumes from burning rubber - ughh!! I think the dust is easier to contain and block than the fumes!

Just my 2 cents worth!!

Thorsteenster · 10-31-2007, 08:14 AM

Wah and boo hoo all you want, a Dremel or a fresh, sharp X-Acto are the best methods for cutting tires.

muddauber7 · 10-31-2007, 09:01 AM

Very soapy water.
dip, cut, repeat...

Thorsteenster · 10-31-2007, 09:29 AM

I got this Dremel attachment I want to try cutting tires with.
http://www.dremel.com/en-us/attachme...=69679&I=69804

Barillms · 10-31-2007, 11:30 AM

Wood burners/ soldering irons.. SOME have a "hot blade" attachment, that is basically an exacto blade that gets hot. They have them a Lowes.
It's like $18.

A 1:1 tire grooving gun is the same philosophy.

If your too big of a wuss to cut a soft rubber toy tire with a cold knife or dremel, I guess
you need to resort to the above tool.

Thorsteenster · 10-31-2007, 11:35 AM

My sister has a Black and Decker soldering iron that came with a few tips. One being an X-Acto blade, it did little more than smoke and stink the place up.

blue95xj · 10-31-2007, 01:59 PM

My buddy has a tire groover meant for grooving 1:1 tires which it's basically a soldering iron with a loop blade on it. I think he said it was like $80 but i don't know where.

Barillms · 10-31-2007, 06:12 PM

Whew, stinkY!!!!!!!

rockmike · 11-01-2007, 02:09 PM

Quote:

Originally Posted by blue95xj

My buddy has a tire groover meant for grooving 1:1 tires which it's basically a soldering iron with a loop blade on it. I think he said it was like $80 but i don't know where.

pmz group is a name of a company i bought my 1:1 tire groover from it cost $65.00 great people to deal with.Personally for these little guys i like the dremel method.

rockmike · 11-01-2007, 02:11 PM

Quote:

Originally Posted by Barillms

Whew, stinkY!!!!!!!

not stinky at all with a fresh blade blast through it like but

ter.

RCMFMaxxMan · 11-01-2007, 04:07 PM

i like wire cutters (side cutters would probably be good too)

andres-tavares · 11-01-2007, 04:31 PM

i will have to buy that accesory for my dremel

thanks

SeanD · 11-02-2007, 07:42 AM

The Dremel saw accessory looks a little bit too "aggressive" and overkill for cutting these small tires. I can see the teeth cutting too easily and you end up going right through the tire. I am not sure if you can remove it or not, but I can see the blade guard really getting in the way while doing the more "close" work of removing lugs. If you look at the User Manual for this attachment, you see that its really only used for straight cross/rip cuts on solid materials. I don't think it would be suitable for cutting rubber lugs - I'd venture a guess to say even quite dangerous to use in this instance.

The stacked cutoff wheels work great - its very easy to control the rate of cut because you are not using saw teeth. They are also VERY cheap and they will not wear out if you are only cutting rubber lugs.

Sean

Big Mike · 11-02-2007, 08:02 AM

I did a similar treatment to some old Mashers with nothing more than a pair of small side cutters.

It did'nt help much...

c0astie31 · 11-02-2007, 01:50 PM

i used a hobby knife to sipe the tire,and a set of side cutters to cut the lugs, i have a set of imex a/t's i did up, just waiting for my chassis to show up to test them out

Szczerba · 11-05-2007, 04:47 PM

I used this dremel attachment on some Imex K-Rocks, well one of them so far. Depends on tire though. I do recommend safety glasses, gloves and long sleeve shirt for this dremel attachment.

http://img221.imageshack.us/my.php?image=1013665ko1.jpg
http://img221.imageshack.us/my.php?image=1013640cg9.jpg

Trike Kid · 11-07-2007, 09:43 PM

I use body scissors or a pair of scissors I modded to do tires with to modify tires most of the time. The set I modded are just a normal set of craft scissors with the blades cut down in length till they were thick enough to not just flex around the rubber. If I'm just siping I use a razor knife or box cutter.

10-30-2007, 04:49 PM	#1
andres-tavares Rock Crawler Join Date: Aug 2006 Location: On the trail Posts: 668	Tips for cutting tires hi i want to give a mashers 2000 looks to my tlt stock tires how can i do that?? thanks

11-02-2007, 07:42 AM	#16
SeanD Rock Crawler Join Date: Apr 2007 Location: St. John's Posts: 548	The Dremel saw accessory looks a little bit too "aggressive" and overkill for cutting these small tires. I can see the teeth cutting too easily and you end up going right through the tire. I am not sure if you can remove it or not, but I can see the blade guard really getting in the way while doing the more "close" work of removing lugs. If you look at the User Manual for this attachment, you see that its really only used for straight cross/rip cuts on solid materials. I don't think it would be suitable for cutting rubber lugs - I'd venture a guess to say even quite dangerous to use in this instance. The stacked cutoff wheels work great - its very easy to control the rate of cut because you are not using saw teeth. They are also VERY cheap and they will not wear out if you are only cutting rubber lugs. Sean Last edited by SeanD; 11-02-2007 at 07:52 AM.

10-31-2007, 06:02 AM	#2
RCholic Pebble Pounder Join Date: Aug 2006 Location: in "Joisey" Posts: 151	I too has wondering how guys "cut or grind" the tire tread... more so what tools they use? I tried searching but am not find the right wording... everything comes up for making tires out of 2 different sets.

10-31-2007, 06:18 AM	#3
OldNube Rock Stacker Join Date: Sep 2006 Location: Coeurdalene Posts: 79	I tried a dremel...............messy I tried a hobby knife.......painful Now I'm looking for some kind of end for my soldering iron that might work. Some kind of loop so you could pick (melt / cut) off individual lugs.

10-31-2007, 06:51 AM	#4
SeanD Rock Crawler Join Date: Apr 2007 Location: St. John's Posts: 548	While the Dremel may be messy, its probably the quickest, safest and neatest. I took the Dremel to my stock Wheely King tires. First I used three cutoff wheels stacked together to cut channels in the lugs. These wheels eat away the rubber pretty quick and with good control. It does kick up a lot of rubber dust so make sure you are wearing a mask. Once I had the lugs cut down, I used a small sanding drum (again on the Dremel) to thin out the tire carcass and to do general clean up around the areas cut by the cutoff wheels. They ended up looking like this: As for the mess, the rubber dust looks dirty but it actually just brushes off and leaves no stain or permanent mark. If you do this outside or in a work area, the cleanup is pretty easy. The big thing is protect your mouth/nose/eyes - just like you would when working with a Dremel anyway. As for burning the lugs, I take the rubber dust anyday to the most-likely toxic fumes from burning rubber - ughh!! I think the dust is easier to contain and block than the fumes! Just my 2 cents worth!!

10-31-2007, 08:14 AM	#5
Thorsteenster I wanna be Dave Join Date: May 2006 Location: Arlington, VA Posts: 3,377	Wah and boo hoo all you want, a Dremel or a fresh, sharp X-Acto are the best methods for cutting tires.

10-31-2007, 09:01 AM	#6
muddauber7 RCC Addict Join Date: Jan 2006 Location: The "Hive" Posts: 1,547	Very soapy water. dip, cut, repeat...

10-31-2007, 09:29 AM	#7
Thorsteenster I wanna be Dave Join Date: May 2006 Location: Arlington, VA Posts: 3,377	I got this Dremel attachment I want to try cutting tires with. http://www.dremel.com/en-us/attachme...=69679&I=69804

10-31-2007, 11:30 AM	#8
Barillms Quarry Creeper Join Date: Sep 2007 Location: Steubenville Posts: 249	Wood burners/ soldering irons.. SOME have a "hot blade" attachment, that is basically an exacto blade that gets hot. They have them a Lowes. It's like $18. A 1:1 tire grooving gun is the same philosophy. If your too big of a wuss to cut a soft rubber toy tire with a cold knife or dremel, I guess you need to resort to the above tool.

10-31-2007, 11:35 AM	#9
Thorsteenster I wanna be Dave Join Date: May 2006 Location: Arlington, VA Posts: 3,377	My sister has a Black and Decker soldering iron that came with a few tips. One being an X-Acto blade, it did little more than smoke and stink the place up.

10-31-2007, 01:59 PM	#10
blue95xj Newbie Join Date: Sep 2007 Location: arnold, mo Posts: 20	My buddy has a tire groover meant for grooving 1:1 tires which it's basically a soldering iron with a loop blade on it. I think he said it was like $80 but i don't know where.

10-31-2007, 06:12 PM	#11
Barillms Quarry Creeper Join Date: Sep 2007 Location: Steubenville Posts: 249	Whew, stinkY!!!!!!!

Sponsored Links

11-01-2007, 04:07 PM	#14
RCMFMaxxMan RCC Addict Join Date: Jun 2004 Location: ORegon Posts: 1,002	i like wire cutters (side cutters would probably be good too)

11-01-2007, 04:31 PM	#15
andres-tavares Rock Crawler Join Date: Aug 2006 Location: On the trail Posts: 668	i will have to buy that accesory for my dremel thanks

11-02-2007, 08:02 AM	#17
Big Mike I wanna be Dave Join Date: Oct 2006 Location: Martinsburg WV Posts: 2,781	I did a similar treatment to some old Mashers with nothing more than a pair of small side cutters. It did'nt help much...

11-02-2007, 01:50 PM	#18
c0astie31 Pebble Pounder Join Date: Jan 2007 Location: WEYMOUTH Posts: 114	i used a hobby knife to sipe the tire,and a set of side cutters to cut the lugs, i have a set of imex a/t's i did up, just waiting for my chassis to show up to test them out

11-05-2007, 04:47 PM	#19
Szczerba I wanna be Dave Join Date: Oct 2007 Location: Castle Rock, WA Posts: 8,785	I used this dremel attachment on some Imex K-Rocks, well one of them so far. Depends on tire though. I do recommend safety glasses, gloves and long sleeve shirt for this dremel attachment. http://img221.imageshack.us/my.php?image=1013665ko1.jpg http://img221.imageshack.us/my.php?image=1013640cg9.jpg

11-07-2007, 09:43 PM	#20
Trike Kid RCC Addict Join Date: May 2005 Location: Auburn, WA Posts: 1,191	I use body scissors or a pair of scissors I modded to do tires with to modify tires most of the time. The set I modded are just a normal set of craft scissors with the blades cut down in length till they were thick enough to not just flex around the rubber. If I'm just siping I use a razor knife or box cutter.

RCCrawler Forums

Thread: Tips for cutting tires