RCCrawler Forums

tsaun987 · 01-01-2008, 02:29 PM

I have tlt cvd's, and i need to know what size drill bit i need to make my rims fit.
Thanks
Tyler

Stormin2u · 01-01-2008, 05:35 PM

I have CVDs and my RockSolids Top Guns fit without drilling.

Thorsteenster · 01-01-2008, 06:47 PM

What do you need to drill, if the wheel is a 12mm hex they should fit right on.

tsaun987 · 01-01-2008, 07:31 PM

The hole that the axle shafts go through
The cvd's are to big to fit. Just need to know what size bit.
I must apologize, they are the copies made by drastic sports. You see, when i purcased them, I was unaware what was going on with all of that. I thought it was the same company. Had I known then that they were a copy of another man's design, I would have given Unimoger my money. Sorry in advance, and thank you for your help.
Tyler

Thorsteenster · 01-01-2008, 08:30 PM

If a hole is too small, use a bit the same size as what your trying to fit in it. Isn't that fairly obvious?

tsaun987 · 01-01-2008, 08:36 PM

you sir are correct. I just didnt want to go to big and wondered if someone else had done it and what size they used

BENDER · 01-02-2008, 03:34 PM

The outer axles on the TLT CVD's are .235 diameter, so a 1/4" drill should work fine.

Thorsteenster · 01-02-2008, 03:54 PM

Who needs a ruler with Bender around?

tsaun987 · 01-02-2008, 09:21 PM

Quote:

Originally Posted by BENDER

The outer axles on the TLT CVD's are .235 diameter, so a 1/4" drill should work fine.

Thanks Bender

01-01-2008, 02:29 PM	#1
tsaun987 Quarry Creeper Join Date: Apr 2007 Location: Katy, TX Posts: 482	What size drill bit to make rocksolids fit tlt cvd's? I have tlt cvd's, and i need to know what size drill bit i need to make my rims fit. Thanks Tyler

01-01-2008, 06:47 PM	#3
Thorsteenster I wanna be Dave Join Date: May 2006 Location: Arlington, VA Posts: 3,267	What do you need to drill, if the wheel is a 12mm hex they should fit right on. Last edited by Thorsteenster; 01-01-2008 at 06:50 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-01-2008, 05:35 PM	#2
Stormin2u I wanna be Dave Join Date: May 2007 Location: Taylors Falls just hanging with the MNRCRC crew. Posts: 7,836	I have CVDs and my RockSolids Top Guns fit without drilling.

01-01-2008, 07:31 PM	#4
tsaun987 Quarry Creeper Join Date: Apr 2007 Location: Katy, TX Posts: 482	The hole that the axle shafts go through The cvd's are to big to fit. Just need to know what size bit. I must apologize, they are the copies made by drastic sports. You see, when i purcased them, I was unaware what was going on with all of that. I thought it was the same company. Had I known then that they were a copy of another man's design, I would have given Unimoger my money. Sorry in advance, and thank you for your help. Tyler

01-01-2008, 08:30 PM	#5
Thorsteenster I wanna be Dave Join Date: May 2006 Location: Arlington, VA Posts: 3,267	If a hole is too small, use a bit the same size as what your trying to fit in it. Isn't that fairly obvious?

01-01-2008, 08:36 PM	#6
tsaun987 Quarry Creeper Join Date: Apr 2007 Location: Katy, TX Posts: 482	you sir are correct. I just didnt want to go to big and wondered if someone else had done it and what size they used

01-02-2008, 03:34 PM	#7
BENDER 2006 2.2 National Champ Join Date: Dec 2004 Location: Big Bear Lake Posts: 8,328	The outer axles on the TLT CVD's are .235 diameter, so a 1/4" drill should work fine.

01-02-2008, 03:54 PM	#8
Thorsteenster I wanna be Dave Join Date: May 2006 Location: Arlington, VA Posts: 3,267	Who needs a ruler with Bender around?

Sponsored Links

RCCrawler Forums

Thread: What size drill bit to make rocksolids fit tlt cvd's?