Rock Bouncer TRX-4 chassis - Team Raffee

[durok]

Bolts to stock TRX-4 parts:

https://www.asiatees.com/article?Tea...l-Cage&id=3255

https://www.asiatees.com/display?Tra...d=155216&pid=1

[Tmaxxed]

Pretty sweet looking. $80. Not bad.


Sent from my iPhone using Tapatalk

[WHITE-TRASH]

The stinger is hideous but I don't hate the rest of it as much as I normally hate these cheap cages. This one looks halfway decent.

[ray4624]

would like to see it installed. Looks pretty solid though

[JatoTheRipper]

This should be called the Mullet. Business in the front. Party in the back.

[bbrigg]

Like: Looks businesslike, hinged electronics tray cover (could be altered for easier access with pins instead of screws though), lots of shock mounting options, looks well finished, dead easy to throw on 2.2 wheels.
Not so sure: Weight - 1.82 KG, electronics are up pretty high, no body or interior parts available - yet.
Don't like: My wife won't let me buy it - yet.

[Joshs4x4toyz]

Originally Posted by WHITE-TRASH

The stinger is hideous but I don't hate the rest of it as much as I normally hate these cheap cages. This one looks halfway decent.

No doubt, give the stinger and shock hoops a bigger radius and not bad looking for off the shelf and $80.

[twisted]

well i was going to order one but they are out of stock

[mewalsh100]

Easy enuff to lop off that stinger and add a cross support if needed.

[92fox]

Would like to see one fully built up for sure...looks pretty cool.

[twisted]

bump.. did anyone here get one of these and mounted it up? i seen one on facebook that didnt look all that great. idk if it was mounted correctly or not.

[bbrigg]

I found the one on Facebook too and it doesn't look great but then his wiring is messy and the photos were taken on a cluttered bench. One interesting thing that I noticed is that the stock battery tray fits so my BowHouse LCG tray should be okay too. The stock receiver box looks okay on the front electronics tray as well. Itching. I'm trying hard to think of how to attach some body panels to clean up the look a little bit.

[twisted]

Originally Posted by bbrigg

I found the one on Facebook too and it doesn't look great but then his wiring is messy and the photos were taken on a cluttered bench. One interesting thing that I noticed is that the stock battery tray fits so my BowHouse LCG tray should be okay too. The stock receiver box looks okay on the front electronics tray as well. Itching. I'm trying hard to think of how to attach some body panels to clean up the look a little bit.

i seen another pic and something looks off on how it sits. the wb might be wrong? idk i wish there were clearer pics.

[bbrigg]

I have a couple of questions I have been mulling over while considering buying this cage.

To help push the CoG forward I would increase the wheelbase by using longer links in the rear. Is there a good driveshaft available with an extra 15-20mm of reach?

Would the new Holmes Hobbies 4274 Puller Pro (Smooth edition) motor fit up front? I have a similar sized 1515 Castle in 2200KV but I would expect the HH motor to have better slow control. That motor is just a little too large in diameter and won't fit as it hits the frame rails. The heavier motor would also help move the CoG forward.

[twisted]

one more bump to see if anyone has mounted one of these cages up.

[r season]

I know this is obviously an old thread, but has anyone yet to complete one of these to where they can post a picture of it?

[JatoTheRipper]

Originally Posted by r season

I know this is obviously an old thread, but has anyone yet to complete one of these to where they can post a picture of it?

I do not, but if you find one please post it here!

[AnimalHippie]

It's been a few months since this has been bumped. Anyone have any pics of one of these installed???

[durok]

From Exocaged RC: