I really want the G Made SR03 wheels on my Defender.
 

I have to compliment SVT923 on his amazing write up on wheels, what a fantastic job. He mentioned that the G Made wheel will fit the trx4 and I'm partial to the G made SR03's, but I want to have them 1-2mm wider than the stock defender set-up. The SR03's have a positive 2mm offset. What do I need to do to counter act this positive offset. I plan on mounting the stock Canyon Trail tires. I read about using a narrower tamiya hex nut and extended stub axles with longer threads but I'm new to this and just not sure on what to do. Any and all help is certainly appreciated. I wanted to post a pic of the SR02 but apparently I can't post attachments, but spec's are below. Thanks

Specs:
Width: 22mm
Diameter: 48mm (1.9inch)
Offset: 2mm positive offset
Hex size: 12mm

Re: I really want the G Made SR03 wheels on my Defender.
 

you need longer wheel hubs

Re: I really want the G Made SR03 wheels on my Defender.
 

OK, but how long? Is there a specific size I need?

Re: I really want the G Made SR03 wheels on my Defender.
 

That wheel does not fit if you add portal weights BTW. It easily the heaviest wheels I have owned (2lbs with tires and foams). I'm not a fan of the offset as they rub the steering link on everything I try to put them on. The hub is also built into the wheel so the only option is a wider hex... if it leaves enough threads for a wheel nut. MIP makes extended axles:
https://www.rpphobby.com/product_p/mip18260.htm


They look nice but I've had my set shelved for a few years, I cant really recommend these wheels.

Re: I really want the G Made SR03 wheels on my Defender.
 

I have them on my Camel Trophy Defender with some Dirt Grabbers fitted on them. I use 8mm hexes, but the Dirt Grabber is much smaller tire than the CTs so you might run into clearing issues. You could get 8mm or 10mm brass hexes for quite cheap though.

Here's how they look on my rig. Keep in mind that this hard body is more narrow than the Traxxas one though.

http://www.rccrawler.com/forum/traxx...0-project.html


They are good wheels but you pay premium for them. One downside is that the bolts strip really easy if you are not careful. You can find similar options out there for much less if you are after the vintage Land Rover look.

If I had to do it all over again I would go for the Injora ones

https://www.injora.com/products/4pcs...39450961903664

Re: I really want the G Made SR03 wheels on my Defender.
 

I have those same wheels on my TRX4 Defender with CTs and brass portal covers. 8mm hexes. Had to trim a little of the front Lexan toward the bumper side. Got a little rubbing in reverse at full deletion in one direction but not enough that it bothers me and no damage/wear and tear to the body.

Re: I really want the G Made SR03 wheels on my Defender.
 

So, some questions answered with a bunch of additional unknowns. I just hope you all stick with me and put up with my ignorance. Really sweet rig Xagorus, damn nice. Yes, I checked out MIP, thanks Humbolt EF, and a few others, Teal makes a 5mm extended axle out of steel. My confusion???? Why would the stock CT's rub if they were pushed out enough, or were they? Let say I extend my axle 5 mm, add a 10mm hex nut.....with a + 2mm wheel offset (SR03's), wouldn't that give me a 3mm increase in stance on each side. Plus their should be no rubbing. Is their a way to get this down to a 2mm increase?

Re: I really want the G Made SR03 wheels on my Defender.
 

Look what I just cam across. Thoughts? https://www.jteamhobbies.com/product...-d90-4pc-white

Re: I really want the G Made SR03 wheels on my Defender.
 

There are a lot of variable and unfortunately no exact answer unless someone has the exact set up you do. Keep in mind, if the tire wheel combo rubs on the steering link or frame and you widen the wheel track with wider hexes, you may have solved chassis rubbing but may now have body rubbing. Also, the how high you have the body mounted as well as suspension droop can all effect that. What I did was purchase three different size hexes and then experimented with the wheel/tire combos I had. At the same time, widening the wheels can cause some additional issues in it self. The farther the contact patch with the surface gets from the actual steering pivot point, the more stress you're causing on steer components, especially the servo. Only go as wide as you need.

Actually the experimenting is all part of the fun. Enjoy!

Re: I really want the G Made SR03 wheels on my Defender.
 

Since the Traxxas Defender comes with the CTs anyway, it wouldn't be a problem to use any 1.9 wheels as long as you figure out what hexes work best. CTs are around 120mm wide, but they tend to get flater as they are used. I'd say, start with 8mm ones, which are +3mm from the stock ones. If you see you need more you can go to 10mm ones.