RCCrawler Forums

RCCrawler Forums (http://www.rccrawler.com/forum/)
-   Vendors Electronics (http://www.rccrawler.com/forum/vendors-electronics/)
-   -   Winch Controller for Radio with 2 Position Third Channel (http://www.rccrawler.com/forum/vendors-electronics/286855-winch-controller-radio-2-position-third-channel.html)

heyok 02-02-2011 10:16 PM

Right. Not sure how to help with that one!

arcticjeff 02-04-2011 01:24 PM

Really intersted in one of these. I toasted my sending unit that came with the winch. I can only get it to come in. when I press the botton. Works on another guys hook-up.

I do have a question. My aux spot already has my BEC plugged into it. I picked up a y adapter to run the original set up. Let me know if this will still work and I'll take one.

heyok 02-04-2011 05:19 PM

Quote:

Originally Posted by arcticjeff (Post 2906230)
Really intersted in one of these. I toasted my sending unit that came with the winch. I can only get it to come in. when I press the botton. Works on another guys hook-up.

I do have a question. My aux spot already has my BEC plugged into it. I picked up a y adapter to run the original set up. Let me know if this will still work and I'll take one.

Yes, the Y adapter will get your BEC power to feed everything. If you like, I can build a Y adapter into your winch controller. Just let me know.

I take it that your third channel is the two position type?

arcticjeff 02-04-2011 06:21 PM

I already have the y adapter so no problem there. How do I buy one of these from you. I have a paypal account so just let me know.

rcdude 03-03-2011 08:38 PM

Quote:

Originally Posted by squatch71 (Post 2902709)



i know thats 4 the 9500 bulldog winch but do u no if it will work with the 9300 bulldog winch?

heyok 03-06-2011 04:51 PM

Quote:

Originally Posted by arcticjeff (Post 2906748)
I already have the y adapter so no problem there. How do I buy one of these from you. I have a paypal account so just let me know.

Sorry, I just saw your message now. I will send you a PM with paypal info.
Quote:

Originally Posted by rcdude (Post 2964636)
i know thats 4 the 9500 bulldog winch but do u no if it will work with the 9300 bulldog winch?

That controller looks like it will run a brushless motor (has three output wires). My controllers are for brushed motors only.

If you are asking me if that controller will work with the 9300 Bulldog Winch, sorry, I don't know. If the motor has three connections, then it will probably work.

heyok 03-15-2011 09:38 AM

Just letting you all know that I've had to raise my prices slightly. I don't do this lightly, but at the same time, I can't build these for free. My time does have some value.

The new price for the Winch Controller for Two Position Channel is $30

Regards,
Al

EastTnCrawler 03-23-2011 03:15 PM

Do you still have any winch controllers for a 2 position 3 channel traxxas radio? I've got a traxxas 2239 2.4 HO. Will this work?

Oh and I've got a 3 racing winch 1/10. Can you run the regular winch controller with 2s on stock AE-2 esc and be fine or do I need the high voltage and a BEC?

I've got paypal like everybody else too lol

Thanks!

heyok 03-23-2011 03:16 PM

Quote:

Originally Posted by EastTnCrawler (Post 3002922)
Do you still have any winch controllers for a 2 position 3 channel traxxas radio? I've got a traxxas 2239 2.4 HO. Will this work?

I've got paypal like everybody else too lol

Thanks!

Yes, I have them! PM me your email address and I will send you a Paypal Invoice.
Thanks,
Al

msd44 06-04-2011 07:47 AM

I'm going to start building a TTC Truck. This would be great to use with my 3pm setup. Still have any in stock?

heyok 06-04-2011 07:52 AM

Quote:

Originally Posted by msd44 (Post 3125818)
I'm going to start building a TTC Truck. This would be great to use with my 3pm setup. Still have any in stock?

Yes I do!
Just send me a PM with your email address and I will send you a Paypal invoice and get a winch controller out to you.
Thanks!
Al

maneesh.n 07-11-2011 12:25 PM

Feed back about Al service...
 
Hi all,

I bought the winch control from AL few months ago and had some electrical problem with the winch, when communicated to AL, he immediately replaced with the new one and again had the same problem with the second control, which was again replaced FOC. And to my bad luck, the third control also did not work. For this Al asked me to send the winch and the control to him. I sent it to him by post and AL noted some problem with the winch. AL worked on the winch and replaced the control and posted the working video over to me. (below)

http://www.youtube.com/watch?v=WuxhWf363nw


I m narrating this story to let you all know the amazing service commitment Al had and his persistent approach to ensure that the product he sold me did work. I really appreciate his approach and attitude towards service.

I live in Dubai and has not seen this commitment towards "service". I strongly recommend Al and you can blindly, without a second thought can buy products offered by Al.


Thanks Al and appreciate your help for my winch.

heyok 07-16-2011 09:56 AM

Thank you for the kind words, Maneesh.

JdRn 09-11-2011 11:53 AM

Just bought 2 of them 2 weeks ago and they have been out standing! Al is a great guy to deal with and I will be buying few more in the future"thumbsup".

GnarKill 09-27-2011 11:55 AM

Trail ready
 
Couldn't be more stoked. Just installed one on a SF-50 and this thing is a man. So easy to hook up too, just soldered right onto the servo motor and replaced the guts with the new controller, presto. Working high torque winch with no "hacking" my FlySky FS-GT3b. Got exactly whats advertised and it did exactly what I wanted. Im kinda rough on stuff so i waterproofed the servo case and first test hauled up about a 5lb propane bottle on some 10lb test effortlessly. Ill ruin the servo before the switch but Ill be back for more anyways, thanks.

crawlin now 12-03-2011 09:53 PM

heyok,
do you have any of these 2 position switch controllers on hand i could use one

heyok 12-04-2011 12:34 AM

Quote:

Originally Posted by crawlin now (Post 3415260)
heyok,
do you have any of these 2 position switch controllers on hand i could use one

I sure do, how many would you like?
Send me a PM and we can work out the details.
Thanks,
Al

crawlin now 12-12-2011 03:42 PM

i know its been said already but i am going to say it again. great product great service. "thumbsup" Thanks again Al

ussprinceton2004 12-29-2011 06:21 PM

Re: Winch Controller for Radio with 2 Position Third Channel
 
...is it safe to put this winch controller in plasti dip to make it waterproof?..

heyok 12-29-2011 06:40 PM

Re: Winch Controller for Radio with 2 Position Third Channel
 
Quote:

Originally Posted by ussprinceton2004 (Post 3475036)
...is it safe to put this winch controller in plasti dip to make it waterproof?..

It is safe to do so, but I have done the waterproofing for you already with either silicone or plasti dip (depends on what method I'm happiest with at build time).

Thanks for asking!


All times are GMT -6. The time now is 05:30 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com