Go Back   RCCrawler Forums > Vendors > Vendors Market > Vendors Electronics
Loading

Notices

Thread: 4 Amp Relay Output Winch Controller

Reply
 
LinkBack Thread Tools Display Modes
Old 03-26-2017, 02:54 AM   #41
Pebble Pounder
 
Join Date: Feb 2012
Location: NTG Racing - San Diego
Posts: 113
Default Re: 4 Amp Relay Output Winch Controller

Not sure if this has been brought up, I had an issue with my DX4S when in winding mode, it would pull in and stop, pull and stop. I remember reading somewhere, which I can't remember where, that one of the settings had to be increase. I eventually increased the travel to 130% on the aux 3P channel for the winding in, it now works just fine
pmadrid13 is offline   Reply With Quote
Sponsored Links
Old 03-26-2017, 05:10 AM   #42
I wanna be Dave
 
Join Date: May 2007
Location: Vancouver, BC
Posts: 2,376
Default Re: 4 Amp Relay Output Winch Controller

Quote:
Originally Posted by pmadrid13 View Post
Are there any marks or difference to determine if the controller is a "H" version? (I have one with a yellow mark)

I also notice that the "soft start" controller looks different, the winch lead is now by itself on one side, the battery and servo leads are now together on the other side
Controllers with the H option usually have a band of red heat shrink near the receiver plug.

Yes, the wires come out of a different spot if soft start has been installed. There is usually a band of blue heat shrink near the receiver plug.

Those bands are only there when I remember to install them
heyok is offline   Reply With Quote
Old 10-24-2017, 05:14 AM   #43
Newbie
 
Join Date: Oct 2016
Location: East Haddam
Posts: 2
Default Re: 4 Amp Relay Output Winch Controller

I have a Spektrum DX4S and can’t get the winch to function properly. It will only operate the winch in one direction. I can get the winch to stop, but not reverse. Any suggestions?
Csrxf450 is offline   Reply With Quote
Old 10-24-2017, 05:43 AM   #44
I wanna be Dave
 
Join Date: May 2007
Location: Vancouver, BC
Posts: 2,376
Default Re: 4 Amp Relay Output Winch Controller

Quote:
Originally Posted by Csrxf450 View Post
I have a Spektrum DX4S and can’t get the winch to function properly. It will only operate the winch in one direction. I can get the winch to stop, but not reverse. Any suggestions?
Sorry to read about the trouble. I will try and help you in a PM.
heyok is offline   Reply With Quote
Old 01-04-2018, 11:15 PM   #45
Newbie
 
Join Date: Jan 2018
Location: San Antonio
Posts: 2
Default Re: 4 Amp Relay Output Winch Controller

Quote:
Originally Posted by heyok View Post
Sorry to read about the trouble. I will try and help you in a PM.
I have the same problem with spektrum dx4c but mine when I stop the winch start moving in pauses by self and I can hear the heyok controller clicks I have a video to show you I just got it today https://youtu.be/72r4mGHtVVg
Chanok74 is offline   Reply With Quote
Old 01-05-2018, 05:17 AM   #46
I wanna be Dave
 
Join Date: May 2007
Location: Vancouver, BC
Posts: 2,376
Default Re: 4 Amp Relay Output Winch Controller

Quote:
Originally Posted by Chanok74 View Post
I have the same problem with spektrum dx4c but mine when I stop the winch start moving in pauses by self and I can hear the heyok controller clicks I have a video to show you I just got it today https://youtu.be/72r4mGHtVVg
Sorry to read about the trouble. I will try and help you in a PM.
heyok is offline   Reply With Quote
Old 01-05-2018, 01:44 PM   #47
I wanna be Dave
 
Join Date: May 2007
Location: Vancouver, BC
Posts: 2,376
Default Re: 4 Amp Relay Output Winch Controller

For those of you playing along at home, the solution was to adjust the trim control for the winch channel until the winch stopped when the channel was in the center position.
heyok is offline   Reply With Quote
Old 07-07-2018, 05:32 PM   #48
I wanna be Dave
 
Join Date: Jan 2004
Location: Austin Texas
Posts: 3,866
Default Re: 4 Amp Relay Output Winch Controller

Hello! I'm having the same issue noted above. I have attempted to adjust the trim and if I set it to about 30* right of center the winch will stop, but it will only move one direction.
Highmark is offline   Reply With Quote
Old 07-07-2018, 07:21 PM   #49
I wanna be Dave
 
Join Date: May 2007
Location: Vancouver, BC
Posts: 2,376
Default Re: 4 Amp Relay Output Winch Controller

Quote:
Originally Posted by Highmark View Post
Hello! I'm having the same issue noted above. I have attempted to adjust the trim and if I set it to about 30* right of center the winch will stop, but it will only move one direction.
Send me a pm and I will do my best to help.
heyok is offline   Reply With Quote
Reply



4 Amp Relay Output Winch Controller - Similar Threads
Thread Thread Starter Forum Replies Last Post
Winch Controller - Relay Driven - External Power heyok Vendors Electronics 90 08-21-2019 09:30 AM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 08:16 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com