Go Back   RCCrawler Forums > Vendors > Vendors Market > Vendors Tires and wheels
Presenting Shifts, Lightweight n' Flexible Offset Hubs Presenting Shifts, Lightweight n' Flexible Offset Hubs
Home Register Forum Rules FAQ Calendar Mark Forums Read
Loading

Notices

Thread: Presenting Shifts, Lightweight n' Flexible Offset Hubs

Reply
Page 7 of 17 « First 23456 7 89101112 Last »
 
LinkBack Thread Tools Display Modes
Old 08-08-2013, 02:00 PM   #121
RCC Addict
 
Join Date: Jul 2009
Location: Near Boston
Posts: 1,233
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Awesome Man, they look great.

Glad your mailroom found them for you
BC-Brian is offline   Reply With Quote
Sponsored Links
Old 08-19-2013, 07:40 PM   #122
Suck it up!
 
Duuuuuuuude's Avatar
 
Join Date: Mar 2008
Location: Arkansas
Posts: 11,652
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Pm sent!
Duuuuuuuude is offline   Reply With Quote
Old 08-20-2013, 08:59 PM   #123
RCC Addict
 
Join Date: Jul 2009
Location: Near Boston
Posts: 1,233
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Quote:
Originally Posted by Duuuuuuuude View Post
Pm sent!
In the mail.
BC-Brian is offline   Reply With Quote
Old 09-10-2013, 01:12 AM   #124
Newbie
 
Join Date: Feb 2010
Location: Scottsdale AZ
Posts: 43
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
PM sent!
Ricky G is offline   Reply With Quote
Old 09-10-2013, 10:30 AM   #125
RCC Addict
 
Join Date: Jul 2009
Location: Near Boston
Posts: 1,233
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
I sold out of everything I had at the Nationals this past weekend, but have no fear, more shifts will be coming in Monday!

I will have the original shifts, and the slims. PM me to get an order in and they will be shipped out as soon as they get in.
Last edited by BC-Brian; 09-10-2013 at 01:59 PM.
BC-Brian is offline   Reply With Quote
Old 09-12-2013, 07:55 PM   #126
I wanna be Dave
 
Join Date: Jan 2012
Location: williamsport
Posts: 8,649
Default
I haven't had a more useful set of hubs. From rig to rig an swapping wheels with diff offsets depending on the terrain. Add a spacer or take one off. Tap the spare holes for 3mm screws and never worry bout the right screw on hand..

Pm for 4th set sent!

Great job at Nats Brian!
winnerone23 is offline   Reply With Quote
Old 09-17-2013, 04:15 AM   #127
Rock Stacker
 
Join Date: Aug 2013
Location: Sydney
Posts: 60
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Hey Brian, Can you please respond to my PM about invoice for a set of red anodized shifts? Was sent last week. Thanks.
Wolven is offline   Reply With Quote
Old 09-17-2013, 09:21 AM   #128
RCC Addict
 
Join Date: Jul 2009
Location: Near Boston
Posts: 1,233
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Shifts are back in stock, both slims and regulars. No Wait list!

Wolven, I sent you a PM last week about pricing/shipping. I just resent it to you in case you lost the first one.
BC-Brian is offline   Reply With Quote
Old 09-17-2013, 11:20 PM   #129
I wanna be Dave
 
Join Date: Jan 2006
Location: Corruptifornia
Posts: 12,053
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Quote:
Originally Posted by Duuuuuuuude View Post
Brilliant!
Yes and pin drive is less parts to slop.
Natedog is offline   Reply With Quote
Old 09-18-2013, 02:03 PM   #130
RCC Addict
 
Join Date: Jul 2009
Location: Near Boston
Posts: 1,233
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Quote:
Originally Posted by Natedog View Post
Yes and pin drive is less parts to slop.
Yep, one less tolerance stackup. Plus, dropping 4 hexes shaves a handful of grams off your rig.
BC-Brian is offline   Reply With Quote
Old 09-18-2013, 02:27 PM   #131
I wanna be Dave
 
Join Date: Sep 2005
Location: Houston, TX
Posts: 16,952
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Wait, what are these "slims" you speak of?
JeremyH is offline   Reply With Quote
Old 09-18-2013, 03:12 PM   #132
I wanna be Dave
 
Join Date: Jan 2006
Location: Corruptifornia
Posts: 12,053
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Quote:
Originally Posted by T3rry View Post
his caliper says .400 and slw hubs go full on to a hex, so that should be pretty accurate. so that's approx half way between a 350 and 475 slw hub
But i too would like a lower profile version, i know on the rear of my ar60 sporty i run .225s and it's almost too wide at that, so thinner would be better, gives more room for adjustability, i think you could probably shave the entire "square" part off the back and recess the pin in the round part, should make material and machining considerably cheaper too


My question is, what's the ID of the spacer rings? will we be able to get a nut driver in there if we run s300/beef axles?

I would definitely take a mitt full if i could use them as low as .225 or even lower.
Very good points, and great suggestions!
Natedog is offline   Reply With Quote
Old 09-18-2013, 03:34 PM   #133
RCC Addict
 
Join Date: Jul 2009
Location: Near Boston
Posts: 1,233
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
JeremyH, These are the slims.

Quote:
Originally Posted by BC-Brian View Post
Slim Shifts 2.0 are in stock for a limited time. I received 10 sets from the machinist today and will get some more made up if you guys kick and scream for them

Rev 2 has a small raised landing for the wheel nut. Some axles were not threaded far enough for the originals slims to work properly without requiring a spacer behind the wheel nut. These still have a .225" offset and should with all axles.

Some photos of the new design.
Last edited by BC-Brian; 10-20-2014 at 11:30 PM.
BC-Brian is offline   Reply With Quote
Old 09-22-2013, 05:38 AM   #134
Rock Crawler
 
Join Date: Aug 2010
Location: Martinique
Posts: 660
Default
Payment done for an orange set !
CrawlrKing is offline   Reply With Quote
Old 09-22-2013, 09:56 PM   #135
Newbie
 
Join Date: Aug 2013
Location: Baltimore
Posts: 30
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Just ordered a set of slims for my poison spyder. Stock trail ready hubs get eat up in the rear of my truck running 3s. These should be perfect. Cant wait to try them out. I may end up making my own weighted spacers after I upgrade the drivelines.
Tominator06 is offline   Reply With Quote
Old 09-28-2013, 01:48 PM   #136
Newbie
 
Join Date: Aug 2013
Location: Baltimore
Posts: 30
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Got mine in the mail today. Thanks Brian. They look sweet. Cant wait to try them out.
Tominator06 is offline   Reply With Quote
Old 09-29-2013, 09:44 AM   #137
RCC Addict
 
Join Date: Jul 2009
Location: Near Boston
Posts: 1,233
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Glad you like them man.

Quote:
Originally Posted by Tominator06 View Post
Got mine in the mail today. Thanks Brian. They look sweet. Cant wait to try them out.
BC-Brian is offline   Reply With Quote
Old 10-06-2013, 08:43 AM   #138
Rock Stacker
 
Join Date: Dec 2011
Location: Canada, Quebec, Saint-Constant
Posts: 69
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
PM sent
patoff is offline   Reply With Quote
Old 10-24-2013, 12:04 PM   #139
RCC Addict
 
Join Date: Jul 2009
Location: Near Boston
Posts: 1,233
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
First Set of Green shifts done for vertec.
BC-Brian is offline   Reply With Quote
Old 10-24-2013, 06:56 PM   #140
Rock Crawler
 
Join Date: Jul 2010
Location: VOLS!
Posts: 564
Default Re: Presenting Shifts, Lightweight n' Flexible Offset Hubs
Thanks Brain!! I appreciate the great communication along with a great product with nice options
Vertec is offline   Reply With Quote
Reply
Page 7 of 17 « First 23456 7 89101112 Last »


« Previous Thread | Next Thread »

Presenting Shifts, Lightweight n' Flexible Offset Hubs - Similar Threads
Thread Thread Starter Forum Replies Last Post
hubs offset? crawler_jake RC4WD Bully 5 11-25-2011 08:21 AM
Any Wide Offset 12mm Hubs Available? alexchen86 Axial SCX-10 0 01-14-2010 03:35 PM
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


All times are GMT -6. The time now is 09:55 AM.

Contact Us - RCCrawler.com - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2023, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com