New 1.9 Scale Beadlocks from GCM Racing
 

Hiya, we have a ton of new wheel stock >>HERE AT THIS LINK<< so swing by and take a look at the new 1.9 offerings.
All of these 1.9 Beadlocks are now standard Hex mount, all of them are 6 Lug mounting, and we have some polished aluminum and Black Anodized finishes available.

Here's some wheel pics to lay it onto your retina:

GCM Racing - 5-Slot Scale Beadlock 1.9 Rim
http://gcmracing.ca/ccdata/images/imageMain_41_266.jpg

http://gcmracing.ca/ccdata/images/full2_41_266.jpg

GCM Racing - 8-Hole Scale Beadlock 1.9 Rim
http://gcmracing.ca/ccdata/images/imageMain_41_267.jpg

http://gcmracing.ca/ccdata/images/full1_41_267.jpg

GCM Racing - 8-Hole Scale Beadlock 1.9 Rim BLACK
http://gcmracing.ca/ccdata/images/imageMain_41_269.jpg

http://gcmracing.ca/ccdata/images/full1_41_269.jpg

GCM Racing - Baja Detroit BL 1.9 Rim
http://gcmracing.ca/ccdata/images/imageMain_41_117.jpg

http://gcmracing.ca/ccdata/images/full1_41_117.jpg

GCM Racing - 12 Spoke Beadlock 1.9 Rim
http://gcmracing.ca/ccdata/images/full1_41_268.jpg

http://gcmracing.ca/ccdata/images/full2_41_268.jpg

Re: New 1.9 Scale Beadlocks from GCM Racing
 

I got to see the slots up close at Disney. Very nice. "thumbsup"

Re: New 1.9 Scale Beadlocks from GCM Racing
 

Got some nice pics of this rig with the 12 Spoke rims. I like these. Very classy!

https://lh5.googleusercontent.com/-6...IMAG3449_1.jpg

Re: New 1.9 Scale Beadlocks from GCM Racing
 

Very nice!!!

Re: New 1.9 Scale Beadlocks from GCM Racing
 

I am so in! I've got a set of 12 spokes on its was to me as I type.

Re: New 1.9 Scale Beadlocks from GCM Racing
 

Look nice, but do they fit VP six bolt hubs? Obviously the five lug style don't, but what about the six lug wheels?

Re: New 1.9 Scale Beadlocks from GCM Racing
 

None of GCM rims fit VP hubs.

Re: New 1.9 Scale Beadlocks from GCM Racing
 

Do they fit any other hub pattern, RC4WD, Hot Racing or?

Re: New 1.9 Scale Beadlocks from GCM Racing
 

They do not. We provide a mounting hub for each wheel in the kit, there's no additional parts to purchase.
The bolt spacing on these other manufacturer's hubs is much wider than ours, and we opted for the most scale looking setup possible, and so we offer a smaller bolt spacing than all the other manufacuturers.

Re: New 1.9 Scale Beadlocks from GCM Racing
 

OK I see now and your hex adapter allows for more wheel dish while not making the wheels stick out too far, thanks.

Yes, the slots are nice.

Re: New 1.9 Scale Beadlocks from GCM Racing
 

What size is the hardware used in your wheels?

Re: New 1.9 Scale Beadlocks from GCM Racing
 

All our wheels are 2-56 hardware. 3/8 long in the beadlock and 1/4 long in the rotor.

Re: New 1.9 Scale Beadlocks from GCM Racing
 

Thank you, Generis

I am using two different axles and trying to get the track width to match. Any chance I could get the coordinates of the bolt circle? I want to make some brass spacers.

Re: New 1.9 Scale Beadlocks from GCM Racing
 

Sounds smart to make a brass spacer. A bit of outside weight is good, especially centered on the axle like that.
The bolt circle is not in my brain at the moment, I know we use a 0.086 diameter hole though. 3/16 center hole. We have spacer kits in aluminum that are 3mm more offset if that helps.

Re: New 1.9 Scale Beadlocks from GCM Racing
 

Thanks for the info. I need to get the wheels bumped out 3/8 on each side at the front. I thought about using 3 of your spacers on each side. With those tiny little bolts I think they will hold up a lot better being one piece. I am surprised you do not sell different widths.