Venom Beast I just got a venom creeper and i was putting the drive shafts together and this one little piece would not fit its product # is 8318 does any one know why that is or some info that could help. Thanks. |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues 8318 - M2.5 X 2.5mm Set Screw |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues 1 Attachment(s) Here's a pic. |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues I believe if you use the upgraded parts (Pin retainers) the set screws that hold the pins in are not needed. Mine did not fit either, but I changed over to traxxas shafts. |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues Quote:
You have to have the set screws to hold drive shafts on but on the cvd's axle shafts you dont... |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues Can you turn a venom creeper into a venom safari creeper by putting a frame or chassis on it |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues A Venom Safari is a Creeper...with frame rail kit bolted on top and a body and a dig unit. |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues where would i get a frame rail kit at |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues Does the Traxxas 2056 servo come with a servo arm or do you have to buy one? |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues Does the rc4wd 35t motor come with the wires already attached |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues Quote:
Quote:
|
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues what servo arm do u use on a venom creeper with a venom high torque servo |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues i finally got my creeper running and i cant keep the rear diff lock locked any suggestions on what i should do |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues does it have something to do with the screw on the switch |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues I just got my creeper running tday and i was going up this obstacle i made and my right front tire got caught and i hit forwards and snapped the short axle shaft. it sucks i will prbly get one tmrw though |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues i want a more scale rc and i already have the venom creeper so i think i was going to turn the venom creeper into the safari creeper but i dont know what parts to get and could you mount the shocks of the venom creeepr straight up and down by mounting them to the frame. i want the frame rails and everything because i want to put a chevy blazer body on it. |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues Some small aluminum angle or flat bar from the local hardware store can make a cheap and very strong scale ladder frame. |
Re: Just got a Venom Creeper (my first rc) and have a little bit of issues ok and i have a venom 50t motor with a axial ae-1 esc and want it to go a little faster so i was thinking of useing a axial 20t or 27t motor would that work with that esc and all stock parts along with the stock motor pinion gear |
All times are GMT -6. The time now is 04:22 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com