|
| LinkBack | Thread Tools | Display Modes |
08-30-2007, 12:47 AM | #1 |
Quarry Creeper Join Date: Aug 2007 Location: NOR*CAL
Posts: 476
| anyone seen this video (AX-10)
its not mine .. but i haven't seen it posted.. if this is your truck, i'm jealous.. http://www.youtube.com/watch?v=lre18XW5pbg |
Sponsored Links | |
08-30-2007, 01:14 AM | #2 |
Pebble Pounder Join Date: Aug 2007 Location: St. Albert - Canada
Posts: 99
| Bwah Hahaha!
That's what I'm going to do when I get mine... Glad to see it works!
|
08-30-2007, 01:18 AM | #3 |
Quarry Creeper Join Date: Aug 2007 Location: NOR*CAL
Posts: 476
|
i allready moded my controller and got another 645mg.. i just need another set of linkage.. anyone have part numbers for me for all the parts i'll need?? linkage / hiems / etc.. |
08-30-2007, 11:02 AM | #4 |
Rock Crawler Join Date: Jun 2007 Location: Hopewell
Posts: 663
|
That truck is not independent rear steer, no control. Independent rear steer is much better. I just made my links out of some delrin rod I had. There are no specific part numbers that I know of, except the stock front linkage set. I do not know the exact measurements for mine at this time. Just measure the front ones, measure again, then cut the rod to length, tap and thread the rod ends on. Make sure the rod ends you use are the same size as the axials if you use the stock measurements. The ones I used are a little longer so the links were a 1/4 smaller I think. It was very easy, took about 15 minutes to do. You will need: Links: 1/4 or 3/16 Delrin or aluminum rod: http://www.usplastic.com/catalog/pro...ct%5Fid=11291# Allthread: 4-40: http://www.hobbypeople.net/gallery/867291.asp Rod Ends: Traxxas: http://www2.towerhobbies.com/cgi-bin...?&I=LXHGB7&P=M Dremel with cutter for allthread and links Drill or Tap Measuring tape Also, I recommend searching this site. That's how I found out most everything I've learned on here. |
08-30-2007, 11:32 AM | #5 |
Release your anger.. Join Date: Oct 2006 Location: North American Union
Posts: 1,063
| |
08-30-2007, 01:31 PM | #6 |
Quarry Creeper Join Date: Aug 2007 Location: NOR*CAL
Posts: 476
|
aah i see..
|
08-30-2007, 01:32 PM | #7 |
~THE SCALE SHOP~ Join Date: Apr 2006 Location: KILLEEN TX
Posts: 10,056
|
post 4=tech |
08-30-2007, 01:51 PM | #8 |
I wanna be Dave Join Date: Mar 2005 Location: Hiding from Goodall
Posts: 2,518
|
Actually, this belongs in the videos section |
08-30-2007, 02:04 PM | #9 |
I wanna be Dave Join Date: May 2007 Location: Taylors Falls just hanging with the MNRCRC crew.
Posts: 7,843
| |
08-30-2007, 02:11 PM | #10 |
I wanna be Dave Join Date: Mar 2005 Location: Hiding from Goodall
Posts: 2,518
| |
08-30-2007, 02:24 PM | #11 |
I wanna be Dave Join Date: May 2007 Location: Taylors Falls just hanging with the MNRCRC crew.
Posts: 7,843
| |
08-30-2007, 02:30 PM | #12 |
Rock Crawler Join Date: Jul 2005 Location: Rathdrum, ID USA
Posts: 549
|
I thought her name was Betty?
|
| |