• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

T1E ''Ti Fighter''

Nova's Ark said:
The mongoose motor was not in it when I was at Greg's ranch to test. He had the mini pullers in it at the time. I think he was waiting on the Tekin ESC's at the time. The Novak ESC's leave a lot to be desired in terms of tuning options as we all know Novak products do. He had already run the Mongoose motors and ESC's and they did not perform stellar. But apparently the Tekin ESC with the Mongoose Motor works well which means I might have to switch up my 1.9 mini Moon Buggy set up.
Click to expand...

I wonder what turn those brushless motor are Cowboy?

Hey take a look at these little bad boys. Jim told me these will rock in our bergs. Also they will be sensored I was with Jamie from Fastlane machines and Jim told us that he will send Jamie the hold patterns for these and Fastlane is looking to make a motor plate for berg V1 axles.

picture.php
 
Last edited:
saydee1800 said:
I wonder what turn those brushless motor are Cowboy?

Hey take a look at these little bad boys. Jim told me these will rock in our bergs. Also they will be sensored I was with Jamie from Fastlane machines and Jim told us that he will send Jamie the hold patterns for these and Fastlane is looking to make a motor plate for berg V1 axles.

picture.php
Click to expand...

Those are going to be horrible in the Berg. It's got twice the KV we need and I'd bet almost no torque. Looks like they're designed for a 1-2 Lb vehicle. Only way they could work is with a 2:1 gear reduction. Even that would probably suck too.

I really wish that some of these electronics companies would sponsor some of the top drivers in the country. Then we'd get some usable electronics.
 
Nova's Ark said:
Having practiced a little with Greg while he ran this truck, it's just nuts! It's smooth, consistent and makes things look effortless.
Click to expand...
Thanks, Next time will get more crawling in "thumbsup". Had a blast though.

saydee1800 said:
What is that like brushless motor in there?
Click to expand...
The Gooses worked for alittle while but got over heated and went down hill after that. Thay are 4400kv and i needed around 2000kv so i ordered the 2.1 gear redution unit from RC4wd and man what a piece of junk. Nothing worked with it, He said it was made to fit a standered pinion but it didnt(Standerd is .125,Mini motors are .078 and these were .090 Not sure what that fits). And the motor will not mount to the case of the unit even. The gear in the unit will not let the pinion on the motor go all the way in the gear unit housing. I email them about this but thay just played dumb and said nobody else had problems and if i wasnt happy i could send it back. You guys are awesome"thumbsup" ,NOT:roll:.

Nova's Ark said:
The mongoose motor was not in it when I was at Greg's ranch to test. He had the mini pullers in it at the time. I think he was waiting on the Tekin ESC's at the time. The Novak ESC's leave a lot to be desired in terms of tuning options as we all know Novak products do. He had already run the Mongoose motors and ESC's and they did not perform stellar. But apparently the Tekin ESC with the Mongoose Motor works well which means I might have to switch up my 1.9 mini Moon Buggy set up.
Click to expand...

The Tekin RS brushless speedos are the way to go, Super smooth. Now i just need some new motor HH????
 
whoodie said:
Those are going to be horrible in the Berg. It's got twice the KV we need and I'd bet almost no torque. Looks like they're designed for a 1-2 Lb vehicle. Only way they could work is with a 2:1 gear reduction. Even that would probably suck too.

I really wish that some of these electronics companies would sponsor some of the top drivers in the country. Then we'd get some usable electronics.
Click to expand...

No not that KV. He told me much lower.
 
2G's said:
The Gooses worked for alittle while but got over heated and went down hill after that. Thay are 4400kv and i needed around 2000kv so i ordered the 2.1 gear redution unit from RC4wd and man what a piece of junk. Nothing worked with it, He said it was made to fit a standered pinion but it didnt(Standerd is .125,Mini motors are .078 and these were .090 Not sure what that fits). And the motor will not mount to the case of the unit even. The gear in the unit will not let the pinion on the motor go all the way in the gear unit housing. I email them about this but thay just played dumb and said nobody else had problems and if i wasnt happy i could send it back. You guys are awesome"thumbsup" ,NOT:roll:.
Click to expand...

I blew up a HV 6.5 in about 30 sec. Ya that is a company that will never have my money again


2G's said:
T



The Tekin RS brushless speedos are the way to go, Super smooth. Now i just need some new motor HH????
Click to expand...

RS are sweet

John just told me today Brushless sensor Puller Pro in around two week if all goes well. He also said the 400 are the way to go in berg :twisted:

He said the based of the Nue motors
 
Last edited:
i must be geting old!!!!!!! did i read the colorado sign up right:flipoff:
ti fighters are going to be in the house:twisted: glad to see you you going greg!
 
Get back on topic chaps... Im bustin my balls waiting for a set of these bad boys....
 
Here some more advantage's with these axle's
 

Attachments

  • Picture 001.jpg
    Picture 001.jpg
    74.6 KB · Views: 1,489
  • Picture 002.jpg
    Picture 002.jpg
    57.7 KB · Views: 1,493
  • Picture 003.jpg
    Picture 003.jpg
    61.1 KB · Views: 1,532
  • Picture 007.jpg
    Picture 007.jpg
    57.4 KB · Views: 1,478
  • Picture 008.jpg
    Picture 008.jpg
    56.5 KB · Views: 1,452
  • Picture 009.jpg
    Picture 009.jpg
    68 KB · Views: 1,464
Nice work Greg, made some changes to mine last night also. "thumbsup"

So is that 3.5oz each front and 1.5 each rear? LH slugs right?
 
You must log in or register to reply here.

Similar threads

U
Hobby Plus CR-18 Harvester Running Videos (Hill Climb, Rock Crawling)
Replies
0
Views
1K
ursanix
U
Rich Trujillo
Rich Trujillo's "Hulk" F100 Ascender Build
Replies
13
Views
3K
Shinchu
S
H
Berg Evoloution Harvo Style
Replies
10
Views
2K
lt99ls1
L
A
Antigacho SCX10II Truggy MX
2 3 4
Replies
75
Views
28K
antigacho
A
E
Berg t1e moon buggy
Replies
5
Views
1K
Heido
Heido
Back
Top