• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

NIRC. Chit Chat

on 1.9's
rock_rider_04.jpg

rock_rider_03.jpg
 
ohhh yeah

I haven't mentioned anything about this because I wasn't sure it was going to happen... but, I believe I'm about to be the proud new owner of a bad ass C3 chassis!

more info to come "thumbsup"
 
That thing is lookin mean!"thumbsup"

Im bustin ass to try to get my rig done up for sunday! A lot more to do yet!
 
Saydee just said we should cancel.

Thanks, ever since the Wraith was announced I knew the axles were going under this RC4WD Rock Rider chassis! I wanted to stuff my 2 speed in it but it doesn't want to fit. Unless I can figure out a new upper link layout.

This is going to be my basher :twisted:
 
Last edited:
I have one of the 10a CC BEC's that I still have to figure out how to wire up (I know Ive seen the info on here somewhere) but, does anyone have the Castle Link because If im remember correctly, I need to set the voltage to my Savox servo specs.
I have the MMP in another truck and I have the field program card for that. Im not sure if that will tune the BEC but, I dont think so.
 
die-laughing said:
I have one of the 10a CC BEC's that I still have to figure out how to wire up (I know Ive seen the info on here somewhere) but, does anyone have the Castle Link because If im remember correctly, I need to set the voltage to my Savox servo specs.
I have the MMP in another truck and I have the field program card for that. Im not sure if that will tune the BEC but, I dont think so.
Click to expand...

I don't rightly know if it will or not. I can bring my laptop though if need be to tune it.

2011-11-01_00-02-16_2.jpg


Check out the ESC in that picture. Basically I just trimmed some the casing off the wire, and wire the red and black BEC wires as appropriate. Granted had to take off the Deans plug to get some shrink wrap on, but I found that this method works pretty well.

Here is the Castle wiring guide.

cc_bec_wiring_diagram.jpg
 
Thanks, I heard that they ship the BEC's setup for 5.0v and I want 7.4v

My servo specs:

Dual Ball Bearings
Orange Anodized Alum. Heatsink
Weight:62g
Speed: .11 sec/60 deg. @ 7.4v
Torque: 26.0/361 kg-cm/oz-in @ 7.4v

Although, I heard that if I only run the FXR on 2s, I wont need the BEC but, I want to run on 3s.
 
die-laughing said:
I have one of the 10a CC BEC's that I still have to figure out how to wire up (I know Ive seen the info on here somewhere) but, does anyone have the Castle Link because If im remember correctly, I need to set the voltage to my Savox servo specs.
I have the MMP in another truck and I have the field program card for that. Im not sure if that will tune the BEC but, I dont think so.
Click to expand...


i have a Castle Link hook u if you need it. I can bring my laptop if we go this weekend.

On the Savox, you should be fine with 6V. To wire it up, the best (imo) is the connect the red and black to your ESCs battery connectors, plug the receiver connection into the bat or any unused channel on your receiver, unplug your ESC receiver connector and using a fine pointed tool, lift the plastic tab on the center pin and pull it out of the connector. Put shrink-wrap on it for protection. DO NOT cut it. there are time, when you Link it, you will need to reattach it.
 
neillarson said:
i have a Castle Link hook u if you need it. I can bring my laptop if we go this weekend.
Click to expand...

Thats what I said! :)

neillarson said:
To wire it up, the best (imo) is the connect the red and black to your ESCs battery connectors.
Click to expand...

I did it this way initially for the Honcho I did not like it, because the BEC generally goes with the receiver, and when it was soldered to the battery connector, it made it hard to move the battery and connectors around as you were having to drag the BEC wires too. So I went and moved it to where I did instead. Now it does not interfere with battery placement and connecting to the batteries.
 
and it is really hard bouncing between the RC Crawlers forum, the RC Scale Builders forum, the Guitar forum and the Amp forum. Sooner or later I am going to cross post and confuse the hell out of everyone else.

Want to talk about a Fender Hot Rod Delux or a Gisbon ES335 Archtop? I am sure the guys on the other forums would be googling like crazy to find a guitar called the Wraith.
 
So, you think I should set the Savox to 6.0v? The BEC comes preset to 5.0v, while I have to change it anyways.. You dont think its a good idea to set it up with 7.4v and be done with it?

So your saying that I cant quite seal up my electronics box just yet because I have to tune the BEC. Thats cool. Atleast were not having a comp this weekend so, I'll just try to stay dry. That is, if I finish the damn thing by then.

Thanks for offering up the laptops by the way, you guys are the shizznit."thumbsup"
 
i would search the elecs section for a couple posts related to the cc 10a bec and people frying them.

i've fried 3 this past year... just all the sudden a glitchy servo and then no worky. and 2 of those bec's had been installed for years.
 
die-laughing said:
So, you think I should set the Savox to 6.0v? The BEC comes preset to 5.0v, while I have to change it anyways.. You dont think its a good idea to set it up with 7.4v and be done with it?

So your saying that I cant quite seal up my electronics box just yet because I have to tune the BEC. Thats cool. Atleast were not having a comp this weekend so, I'll just try to stay dry. That is, if I finish the damn thing by then.

Thanks for offering up the laptops by the way, you guys are the shizznit."thumbsup"
Click to expand...

Check your servo manual. If you have a HV server like the HS 7954SG, 7.4 is great. But, make sure (if you have 4WS) that you front and rear can handle it.
 
Yeah, I did run across a few threads related to that. I guess I figured I would be ok because I have the new style 10a with capacitor. Well, that and the fact that I was running out of time to get it finished so, I figured something would be better than nothing. So, do you think I should just run no BEC with the FXR on 2s until I can get ahold of the CC BEC 25a?

Edit: I only have front steer.
 
You must log in or register to reply here.
Back
Top