-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
GT3B Hack Question and Answer Thread
- Thread starter losikid
- Start date
TacoCrawler
I wanna be Dave
messaged inquiry to LK...
still avail ?
still avail ?
norcalmk2
Pebble Pounder
Anyone know if the rc4wd blue RX is compatible with the gt3c radio, hacked or not. I am looking to get the hack after I buy my rx/tx and would like to not have to buy a second RX if I don't have to.
Sent from my XT907 using Tapatalk 4
Sent from my XT907 using Tapatalk 4
losikid
Got Worms?
TacoCrawler
I wanna be Dave
norcalmk2
Pebble Pounder
What RX's can I buy with more channels than 3?
Sent from my XT907 using Tapatalk 4
Sent from my XT907 using Tapatalk 4
norcalmk2
Pebble Pounder
Hey losikid I know your a busy man but I thought I may have a better chance contacting you on here. I was just wondering if there's an eta on the gt3b I ordered 2 Mondays ago. Thanks sorry to bother you it's just for my first rc so I'm pretty anxious.
ncampos976
Newbie
So 'm trying tthrottle heforward inder micros with the current firmware. I have gotten to work pretty well when I tried to calibrate the ECS I have to hold the throttle in Reverse to get into programming mode instead of forward like the instructions say. and also if I go into reverse and try to go forward the rear dig stays on even though I didn't turn it on. If i hit throttle forward again rear wheelS come un locked
Turbo-s
Rock Stacker
Hello Gentlemen,
I have a modded GT3B that I updated back in 2012, works fine ever since, haven't touched it. Well I forgot a lot about it now I want to run to sidewinders in a MOA setup for a XR10 comp rig. What do I need to do, do I need a special flash to update?
I have a modded GT3B that I updated back in 2012, works fine ever since, haven't touched it. Well I forgot a lot about it now I want to run to sidewinders in a MOA setup for a XR10 comp rig. What do I need to do, do I need a special flash to update?
Charlie-III
I wanna be Dave
I'm running firmware 0.4 & dual ESC's in an XR-10 with no issues (over a year now).
Search this thread for my screen name and it was last fall I did a tweaked template to program front/rear dig, proportional, etc.8)
I still need to go to version 0.6.:roll:
I`m running 0.6.1 firmware and just went to the templates section on the 2nd post on the thread were is says "Dual ESC mixing templates for firmware 0.6.1".
Follow these instructions and you`ll be set.
There is also a section in troubleshooting that is on the same post and has instructions for older firmwares .
Good luck.
mjderstine
SuperShafty.com
do i need to update my firmware? i bought my card about a year ago.
been trying to setup 4ws and following the template from the link on post 2 i dont get a lot of the options it is telling me, well i'll put some notes in here. just gonna tell you what i don't see and what i do see when i go through the menus. am i just reading things wrong. do i have old firmware? i have 0.6.1
Activate 4WS mix
Long click EPA
4
3
0
NOC i dont see this, i get CR0/1
Long enter
Map the 4WS mix to ST trim Buttons
Long Click REV
1
4WS
NOL don't see this, I see BNL/AR/MO/EN
100
NOR don't see this, I see RE0/1
NOO don't see this, I see OR0/1
Press and hold enter
back
Map CH 3 Button to turn crab on/off
Long click REV
C
4WS
SWI don't see this, I see MO0/1
NOR don't see this, I see RE0/1
NPV don't see this, I see PV0/1
OFF
Press and hold enter
back
Map CH3 Trim switch to control Channel 4
Long click REV
3
CH4
MOM don't see this, I see BMO/EN/NL/AR/RS
THEN I SEE RE0/1
THEN PV0/1
Press and hold enter
back
Map D/R switch to control Channel 5
Long click REV
D
CH5
MOM don't see this, I see BMO/EN/NL/AR/RS
THEN I SEE RE0/1
THEN PV0/1
Press and hold enter
back
been trying to setup 4ws and following the template from the link on post 2 i dont get a lot of the options it is telling me, well i'll put some notes in here. just gonna tell you what i don't see and what i do see when i go through the menus. am i just reading things wrong. do i have old firmware? i have 0.6.1
Activate 4WS mix
Long click EPA
4
3
0
NOC i dont see this, i get CR0/1
Long enter
Map the 4WS mix to ST trim Buttons
Long Click REV
1
4WS
NOL don't see this, I see BNL/AR/MO/EN
100
NOR don't see this, I see RE0/1
NOO don't see this, I see OR0/1
Press and hold enter
back
Map CH 3 Button to turn crab on/off
Long click REV
C
4WS
SWI don't see this, I see MO0/1
NOR don't see this, I see RE0/1
NPV don't see this, I see PV0/1
OFF
Press and hold enter
back
Map CH3 Trim switch to control Channel 4
Long click REV
3
CH4
MOM don't see this, I see BMO/EN/NL/AR/RS
THEN I SEE RE0/1
THEN PV0/1
Press and hold enter
back
Map D/R switch to control Channel 5
Long click REV
D
CH5
MOM don't see this, I see BMO/EN/NL/AR/RS
THEN I SEE RE0/1
THEN PV0/1
Press and hold enter
back
Last edited:
mjderstine
SuperShafty.com
Last edited:
Charlie-III
I wanna be Dave
Sounds like the 4WS template is for version 0.4 and you're running the current version (0.6).
Glad it's working now.
ncampos976
Newbie
Anyone have a idea why my rear dig would activate when I go reverse.?
mjderstine
SuperShafty.com
none here
