Stuck's UCFab PRT HD Well after talking to a few PRT drivers I sent Kyle a message and got the ball rolling. A few months have gone by talking with Kyle and getting all the details together and finally this showed up at my door. What an awesome little chassis. Been collecting parts for the last 5 months for this build. Here is whats in store. UCFab PRT HD Chassis W/ Light bar mount and PRT skid UCFab leading and trailing arms UCFab Sway bars VP Curries F & R with 43/13 UD gears and VP knucks and C's. Axial Wraith universals up front and VP rear shafts VP Light Bar VP trans Case, Steel Gears, Super Shafty extended outputs (still working on a spur/slipper combo) VP KMC Enduro 2.2 Wheels 1.2 wide Pro Line Pro Spec shocks Ottsix 2.2 KLR's Crawler innovations Foams. 5.5 Double Deuce W/ Med outers F&R MIP drive shafts F&R Hitec 7950 Castle MMP Castle BEC Tekin Pro4 4300kv TI F&R upper links Skins. maybe Krawler Konceptz. No template available so I'll need to get crafty Still need to pick up some parts on my list but here is a couple pics of the chassis and its time to get busy! http://www.rccrawler.com/forum/membe...353-63124.jpeg http://www.rccrawler.com/forum/membe...353-63123.jpeg |
Re: Stuck's UCFab PRT HD as always a work of art, I'll be watching this for sure |
Re: Stuck's UCFab PRT HD Been a little busy around here and I haven't had much time to work on the PRT. But I did manage to get a few things done. Sway Bars, Leading and trailing arms. http://www.rccrawler.com/forum/membe...353-63153.jpeg Almost got the axles all buttoned up. Just need to finish greasing them up, install diff covers and truss's http://www.rccrawler.com/forum/membe...353-63154.jpeg |
Re: Stuck's UCFab PRT HD Looks good. Finish this and ill come out just to drive it... |
Re: Stuck's UCFab PRT HD Quote:
Thanks Chump, Get ready. It will be done soon.........I hope:ror: Little more progress. I used some 30mm spacers and 3mm rod ends to make up my sway bar links and got them installed. Should work out fine. I got the shocks and rear axle bolted up as well and had to space the shocks out 6mm to clear the chassis. http://www.rccrawler.com/forum/membe...353-63187.jpeg http://www.rccrawler.com/forum/membe...353-63198.jpeg Only one problem, Axle truss hits the sway bar before full compression. I have a centered pumpkin currie that im gonna swap in and that should cure this problem. http://www.rccrawler.com/forum/membe...353-63194.jpeg |
Re: Stuck's UCFab PRT HD Well I finally got around to swapping out the off center Currie to the centered Currie and it solved my problem of the axle hitting the sway bar. New problem was the axle hitting the chassis but a 5mm external limiter on the shocks and were good to go. http://www.rccrawler.com/forum/membe...353-63231.jpeg A little more travel over the offset axle and it tucks up in the chassis a little now http://www.rccrawler.com/forum/membe...353-63230.jpeg Also got some templates for the skins cut out. Still working on the final shape but its a start. A few more parts are in the mail so I should be able to finish up the drive train soon. Thanks for Looking"thumbsup" http://www.rccrawler.com/forum/membe...353-63232.jpeg |
Re: Stuck's UCFab PRT HD Damn Joel, you have accumulated quite a few rigs since I moved out of the Bayarrhea! Miss crawling with you and carpooling to comps. |
Re: Stuck's UCFab PRT HD what kind of rear upper links you got going on there?! |
Re: Stuck's UCFab PRT HD Quote:
Ya man those were good roadtrips! Quote:
|
Re: Stuck's UCFab PRT HD Well Merry X-Mas to me. VP light bar and Front truss showed up. http://www.rccrawler.com/forum/membe...353-63286.jpeg Time to finally build the front axle. http://www.rccrawler.com/forum/membe...353-63285.jpeg |
Re: Stuck's UCFab PRT HD Axle all done and installed. Still need a few more screws in that cover http://www.rccrawler.com/forum/membe...353-63317.jpeg That drivers side upper link is gonna need some work! Time to bust out the tube bender:twisted: http://www.rccrawler.com/forum/membe...353-63318.jpeg Rigs coming along. Also HAD to get the light bar installed:ror: http://www.rccrawler.com/forum/membe...353-63319.jpeg http://www.rccrawler.com/forum/membe...353-63320.jpeg |
Re: Stuck's UCFab PRT HD Its been a little bit but I had a few parts and pieces show up. My trans and drive shaft parts finally arrived and I was able to finish up the drive train. http://www.rccrawler.com/forum/membe...353-63440.jpeg Front link didn't need much to clear the drive shaft. Just a slight bend and were good. Probably bent it a little more than it needed so I may adjust that a bit later http://www.rccrawler.com/forum/membe...353-63445.jpeg Even clears the chassis cross member "thumbsup" http://www.rccrawler.com/forum/membe...353-63446.jpeg Tires and electronics showed up too8) http://www.rccrawler.com/forum/membe...353-63435.jpeg Gonna mount the KLR's on these Axial Methods for now with CI Double Deuce's. Med outers front and rear. http://www.rccrawler.com/forum/membe...353-63434.jpeg I dropped the skid to make everything a little easier. Made a little bracket to mount the ESC. Ready to go back in! http://www.rccrawler.com/forum/membe...353-63472.jpeg Thanks For looking:) |
Re: Stuck's UCFab PRT HD anyway i could get a better look at that bracket? Looks awesome! |
Re: Stuck's UCFab PRT HD Quote:
http://www.rccrawler.com/forum/membe...353-63517.jpeg |
Re: Stuck's UCFab PRT HD Got some more wrench time in over the weekend. Re installed the skid with all the goodies. http://www.rccrawler.com/forum/membe...353-63518.jpeg Servo and steering installed but noticed horn just barely hits the chassis. Gonna have to take a look at how I can move that servo back a bit. http://www.rccrawler.com/forum/membe...353-63520.jpeg Made a fire wall out of ABS to hide, mount and protect the electronics. Top part will serve as a mounting point for the interior as well. Still have some wire routing and soldering to finish up. http://www.rccrawler.com/forum/membe...353-63521.jpeg Also got the KLR's mounted up. CI DD Foams with medium outer ring F/R. Still need to settle on a track width and get some hubs. If they work as good as they look I'll be alright8) http://www.rccrawler.com/forum/membe...353-63519.jpeg Thanks for looking "thumbsup" |
Re: Stuck's UCFab PRT HD You are far more patient than I am. If I don't get a new build together in a couple days I lose my mind. I'm in line for one of these as well. I have everything I need to get it together the day it arrives. lol |
Re: Stuck's UCFab PRT HD I wanna see this thing in person! Sweet build Joel"thumbsup" |
Re: Stuck's UCFab PRT HD Quote:
Quote:
|
Re: Stuck's UCFab PRT HD Well Im almost there! I really wanted a spur cover so I found a stock Axial Wraith Slipper, motor plate and cover on Ebay for $14 and swapped out the AX10 slipper and BWD motor plate. Looking at the Super Shafty motor plate option to bring back some rigidity I lost going back to the stock plate. We'll see how it holds up. http://www.rccrawler.com/forum/membe...353-63645.jpeg Fabbed up a battery tray out of ABS. http://www.rccrawler.com/forum/membe...353-63651.jpeg Battery tray installed, skid back in and all wires routed. http://www.rccrawler.com/forum/membe...353-63647.jpeg And Its RTR! Smallest hubs I had were some 750's which puts me @ 12 3/8 width. Aiming for about 11 3/4 to 12". I think some 450's might be the ticket. http://www.rccrawler.com/forum/membe...353-63649.jpeg http://www.rccrawler.com/forum/membe...353-63646.jpeg HPI Interior installed. http://www.rccrawler.com/forum/membe...353-63641.jpeg I transferred my cereal box templates ;-) onto some lexan and my skins are ready for some paint! After that I need to do some shock tuning and were ready to hit the track"thumbsup" http://www.rccrawler.com/forum/membe...353-63643.jpeg Thanks For Looking"thumbsup" |
Re: Stuck's UCFab PRT HD Been a little bit since I worked on this. Had a little problem with my Achilles ( I detached it) so the garage hasn't been the most comfortable place. So heres a little update. I picked up a Duuuuude De-wanger to fix my servo hitting the chassis problem. Hopefully this fixes the issue. http://www.rccrawler.com/forum/membe...353-63705.jpeg Also had a little problem with the skid. Not sure how this happened, but it did. Kyle sent me another skid, but its unfinished. Supposedly every chassis is different and they cant drill it. Looks like I have to drill my own mounting/lower link holes and widen the pockets a bit because the ball ends wont even fit. Not happy about that but it will give me something to do while im laid up. last skid was milled out and the new one is solid so I don't think I'll have this problem again. http://www.rccrawler.com/forum/membe...353-63816.jpeg Lastly I decided to upgrade the Axial plastic Methods. I just didn't trust them to be reliable so I picked up a set of VP KMS Enduor 1.2 wide wheels during the RPP sale. I had some blue rings laying around so I thought I would use those to add a touch of detail to match the other blue parts. Just have to build the last 2 and mount up the KLR's "thumbsup" http://www.rccrawler.com/forum/membe...353-63814.jpeg Thanks for Looking! |
All times are GMT -6. The time now is 04:11 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com