Re: RBX10, RYFT, Scale Rock Bouncer Quote:
Another short vid... https://youtu.be/7zStdSRH2NQ |
Re: RBX10, RYFT, Scale Rock Bouncer Just ordered a HH SHV500v3 and a Mamba X 1415 combo for mine "thumbsup" |
Re: RBX10, RYFT, Scale Rock Bouncer Quote:
|
Re: RBX10, RYFT, Scale Rock Bouncer Quote:
Just curious |
Re: RBX10, RYFT, Scale Rock Bouncer Quote:
|
Re: RBX10, RYFT, Scale Rock Bouncer Quote:
https://i.postimg.cc/sxR78LCm/497-CE...-E233500-D.jpg It off a HPI Venture with a STRC arm and cam "thumbsup" |
Re: RBX10, RYFT, Scale Rock Bouncer Thank you guys for your advise "thumbsup" |
Re: RBX10, RYFT, Scale Rock Bouncer |
Re: RBX10, RYFT, Scale Rock Bouncer Quote:
My servo saver is getting really sloppy now, and I am debating just removing it for a straight arm... |
Re: RBX10, RYFT, Scale Rock Bouncer Quote:
|
Re: RBX10, RYFT, Scale Rock Bouncer Quote:
|
Re: RBX10, RYFT, Scale Rock Bouncer Added problem with that floppy servosaver, is that at high speeds, the AVC gets completely discombobulated, trying to compensate for the wheels flopping about, and as a result usually a Death Walk, and a cartwheel because the tires balloon independent of each other due to the open diffs. Only way to stop that is completely disabling AVC.. Which makes fast starts a problem because f the lack of sways. Ugh. Did Axial even tèst the thing at 4s? On a flat, dry road it’s manageable, but on even slightly rough terrain, it’ll bounce and roll around like a tumbleweed on even the slightest provocation. “Ill conceived” would be an understatement. Ah, well. A Losi LMT servosaver is on its way. ( expensive little trinket, though.. ) |
Re: RBX10, RYFT, Scale Rock Bouncer New electrics arrived for one today, the motor is a tight fit and looks like it may rub slightly on the front outer lower link rod end https://i.postimg.cc/4N52PsNv/416316...6-D78-C156.jpg |
Re: RBX10, RYFT, Scale Rock Bouncer Electrics are in! https://i.postimg.cc/63K8g7nb/B144-D...-A816487-B.jpg What a huge difference, yes I know it’s a bouncer and doesn’t really need the low end control, but it’s nice to have it and the combo will also have more power than stock, so it a win win to me https://youtu.be/riGmvmutLsY |
Re: RBX10, RYFT, Scale Rock Bouncer Quote:
|
Re: RBX10, RYFT, Scale Rock Bouncer “More power than stock” ehrm.. not really needed for me...My word.. The Spectrum 2200kv is already crazy overpowered ( remember : 61km/h @ 3s GPS confirmed) But that sensored setup ... O_o Quite the difference. Suddenly it’s much more versatile. “Best of both worlds’ And no more annoying “brr.rr.rr.rrrr” too. By the by, how did You make the beef tubes? Cut them to the right diameter Yourself? And how do You affix them inside the axles, epoxy glue? |
Re: RBX10, RYFT, Scale Rock Bouncer It will be slower than stock with the 14t pinion I’m fitting, it’s a hotter combo for sure, but with my radio gear and the excellent Castle firmware I can tune it exactly how I want. I machined the tubes to fit and they are a tolerance fit |
Re: RBX10, RYFT, Scale Rock Bouncer Ah. Thank You. Hmm.. I cannot machine. But I dìd find an aluminium tube that ‘almost fits’ I hope the 0.10mm left will be filled adequately with epoxy. I haven’t broken anything yet (apart from sway arms that worked themselves loose, despite red locktite) but am still apprehensive that the front axle will snap. Oh. I dìd purchase the aluminium plates for the rear arms, because they already began showing signs of material fatigue. Just 4 packs in. I wonder if the shorter Integy arms for the Yeti will fit if I attach the rear brackets upside-down, thereby compensating the missing Cm of the yeti link compared to the Ryft.. *pondering* But, well, I gather a sensored setup will be in the near furure for me. Maybe for the kit. ( yes, that one will be coming too. If only for the included 2-speed. I lóve me some extra technical gizmo’s) ) |
Re: RBX10, RYFT, Scale Rock Bouncer The Losi Baja Rey 1/10 trailing arms are about the same length, I’m not sure about the sway bar fitment though |
Re: RBX10, RYFT, Scale Rock Bouncer Quote:
Quote:
Is that video with the 14t pinion? |
All times are GMT -6. The time now is 02:43 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com