| |
| |||||||
 |
| | LinkBack | Thread Tools | Display Modes |
06-18-2013, 06:55 PM
| #1 |
| Newbie Join Date: May 2013 Location: mesa
Posts: 5
|  after work crawl at falcon hill
well a few photos before I got attacked by bees lol trying out my new crawler motor with new tranny gears to climbs like a beast now lol Mobile Photobucket Mobile Photobucket |
|  |
| Sponsored Links | |
| | |
|
06-18-2013, 08:07 PM
| #2 |
| RCC Addict Join Date: Jun 2011 Location: Gilbert, AZ
Posts: 1,634
|
What motor you end up going with? Sent from the can using Tapatalk |
|
| |
|
06-18-2013, 10:10 PM
| #3 | |
| Newbie Join Date: May 2013 Location: mesa
Posts: 5
| Re: after work crawl at falcon hill Quote:
| |
|
| |
|
06-18-2013, 10:39 PM
| #4 |
| RCC Addict Join Date: Jun 2011 Location: Gilbert, AZ
Posts: 1,634
|
Maybe 52/11 or 62/11 gears? Sent from the can using Tapatalk |
|
| |
|
06-19-2013, 09:51 AM
| #5 | |
| Newbie Join Date: May 2013 Location: mesa
Posts: 5
| Re: after work crawl at falcon hill Quote:
 | |
|
| |
|
06-19-2013, 11:31 AM
| #6 |
| RCC Addict Join Date: Jun 2011 Location: Gilbert, AZ
Posts: 1,634
| Re: after work crawl at falcon hill
Wow that's a 2.9:1 ratio. Watch your motor/ESC temps. Likely to get hot, specially if you are running any timing in your motor. I am running 5:1 and have ran up to 5.8:1 for crawling. Maybe we aren't talking the same language. When I'm talking gearing mine is 80/16, I'm saying I run 80 tooth spur and 15 tooth pinion. Without modding the motor mount, I couldn't use any smaller combination. The motor is all the way over in the slots to get the mesh set right. |
|
| |
|
06-19-2013, 03:21 PM
| #7 | |
| Newbie Join Date: May 2013 Location: mesa
Posts: 5
| Re: after work crawl at falcon hill Quote:
| |
|
| |
|
06-19-2013, 03:23 PM
| #8 |
| Newbie Join Date: May 2013 Location: mesa
Posts: 5
| Re: after work crawl at falcon hill
I had to mod my gear case for the 32 tho so I have a lil space open but other then that it all fits fine and I ran it for a hour in 105 degree weather and it wasnt even hot
|
|
| |
|
06-19-2013, 06:59 PM
| #9 |
| Newbie  Join Date: Jul 2012 Location: Queen Creek Az
Posts: 20
| Re: after work crawl at falcon hill
32 PITCH, 60 tooth spur with an 11 tooth pinion perhaps?
|
|
| |
|
06-19-2013, 07:45 PM
| #10 | |
| Newbie Join Date: May 2013 Location: mesa
Posts: 5
| Re: after work crawl at falcon hill Quote:
 | |
|
| |
|
06-19-2013, 08:58 PM
| #11 |
| RCC Addict Join Date: Jun 2011 Location: Gilbert, AZ
Posts: 1,634
|
Yeah that would be a better ratio. I was trying to leave pitch out of the equation to simplify it some. But ultimately pitch doesn't matter so long as they are the same on both gears. Sent from the can using Tapatalk |
|
| |
|
after work crawl at falcon hill - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| FALCON HILL SUNDAY 1/20 9 am | Sheepdawg23wm | Arizona | 14 | 01-21-2013 04:55 PM |
| Falcon Hill on Thursday...maybe | Big Daddy | Arizona | 14 | 10-08-2011 03:51 PM |
| Falcon Hill 10/11/09 THANKS | Minitrucker69 | Arizona | 7 | 10-11-2009 06:13 PM |
| Falcon Hill in the AM | BikeDad | Arizona | 3 | 10-02-2009 11:04 PM |
| falcon hill 6/12 | robbio4422 | Arizona | 11 | 06-12-2009 11:08 PM |
| |
Linear Mode
