Re: Locked Up's SCX10 II Quote:
great thread! wheels look awesome, now to continue reading |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. Random servo added just to get through the build. http://www.lockeduprc.net/misc/pictu...I/IMG_4007.jpg |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. End of page 25. Driver side frame assembled. DO NOT forget to run your servo wire under the cover (bottom of page 25) if you are going to use it. Otherwise you will get to disassemble a few things. http://www.lockeduprc.net/misc/pictu...I/IMG_4012.jpg Note: When attaching the front cross member, my holes/nubs did not line up. My fix was to slice off the numbs. http://www.lockeduprc.net/misc/pictu...I/IMG_4008.jpg http://www.lockeduprc.net/misc/pictu...I/IMG_4009.jpg |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. Quote:
|
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. Quote:
Thanks. Will correct that in a second. Connecting the CMS, I noticed the drag link rod end angles max out before I want them to. This is at rest: http://www.lockeduprc.net/misc/pictu...I/IMG_4016.jpg I started to connect to the servo arm and I realized the arm I had wanted to use (for scale appearance) was going to have the draglink and track bar out of alignment. They are aligned in the pic but that screw is not tightened.... yes the 2mm matters to me. http://www.lockeduprc.net/misc/pictu...I/IMG_4017.jpg So I busted out a trusty Axial part from the stash. The alignment looks dead on, but there is still a bit of pull on that draglink. http://www.lockeduprc.net/misc/pictu...I/IMG_4018.jpg http://www.lockeduprc.net/misc/pictu...I/IMG_4019.jpg |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. Rear end going in and got a surprise. We had rotated the lock outs to hide the screws, but had to remove to put the lower end of shocks on. This is only because of how we mounted the lockouts. http://www.lockeduprc.net/misc/pictu...I/IMG_4020.jpg http://www.lockeduprc.net/misc/pictu...I/IMG_4021.jpg We like to run around and stick our shafts in things... http://www.lockeduprc.net/misc/pictu...I/IMG_4022.jpg End of page 29... http://www.lockeduprc.net/misc/pictu...I/IMG_4023.jpg http://www.lockeduprc.net/misc/pictu...I/IMG_4024.jpg |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. The electronics box looks nice. The screws that hold the top on are PLENTY long enough to really crank down on it. http://www.lockeduprc.net/misc/pictu...I/IMG_4025.jpg On the back side you have an additional silicone gasket for the servo leads. I'm guessing you'd want to slather the extra holes with liquid electrical tape or sealant of some sort if you are not using them all. http://www.lockeduprc.net/misc/pictu...I/IMG_4026.jpg |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. Putting the bumpers on and that front is just begging for a Commando Winch System. The holes lined up too.... http://www.lockeduprc.net/misc/pictu...I/IMG_4029.jpg I did go ahead and drill 2 holes in the bottom of the bumper to make it easier to install the screws in the bottom. http://www.lockeduprc.net/misc/pictu...I/IMG_4030.jpg I do recommend slightly longer screws because the Axial bumper is thicker than the 3Racing plate/fairlead combo. Yes. I got rid of the 3Racing fairlead because our Aluminum fairlead is just such a close match and looks great! http://www.lockeduprc.net/misc/pictu...I/IMG_4031.jpg I finished it all out with our Winch Saver, Scale Winch Hook and 250lb Yellow Winch Line. http://www.lockeduprc.net/misc/pictu...I/IMG_4032.jpg And finally the mounted shots of both the front and rear. http://www.lockeduprc.net/misc/pictu...I/IMG_4033.jpg http://www.lockeduprc.net/misc/pictu...I/IMG_4034.jpg |
Locked Up's SCX10 II Build- In progress now. Yes. Right now. So do your rear shafts fit in these axles Sent from my iPhone using Tapatalk |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. Roller! http://www.lockeduprc.net/misc/pictu...I/IMG_4036.jpg http://www.lockeduprc.net/misc/pictu...I/IMG_4037.jpg http://www.lockeduprc.net/misc/pictu...I/IMG_4038.jpg http://www.lockeduprc.net/misc/pictu...I/IMG_4039.jpg And THAT ..... is where we leave off for the night. I don't like painting to begin with but tired+paint=trouble. "thumbsup" |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. Quote:
Tangs are a little different ... but we like to fart around. ;-) |
re: Locked Up's SCX10 II Build Some Lockedup RC shackles front and rear would look good. ;-) |
Re: Locked Up's SCX10 II Build- In progress now. Yes. Right now. Quote:
|
re: Locked Up's SCX10 II Build Good tip. Will look for those. |
re: Locked Up's SCX10 II Build Quote:
|
re: Locked Up's SCX10 II Build on the steering link an cms link I installed the angled rod ends, the straight rod ends wont work too good with out binding, just a hint |
re: Locked Up's SCX10 II Build Quote:
:lmao: Eric did the first part of the build so when I got around to the links I just installed what he had built. Will swap those tonight and get some shackles on there as well! |
Re: Locked Up's SCX10 II Build We got delayed when we realized I forgot the paint... but back on track now. Eric got the body cleaned up and masks installed: http://www.lockeduprc.net/misc/pictu...I/IMG_4048.jpg |
All times are GMT -6. The time now is 07:39 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com