02-11-2014, 12:31 PM | #1 |
RCC Addict Join Date: Nov 2009 Location: cleveland,Tn
Posts: 1,331
| Cms/panhard issue
I was not gonna do a thread on this but I have ran into a problem and was gonna see what other people had done to solve the problem I just installed the vp cms and panhard kit and I'm running the proline rear slash shocks and I have less than a 1/4 of travel in the front I'm running the shocks in the middle hole in the front and I didn't think moving it to the front hole it would raise it up enough for clearance just by moving it to the front most hole
|
Sponsored Links | |
02-11-2014, 12:58 PM | #2 |
Quarry Creeper Join Date: Dec 2008 Location: Santa Mira
Posts: 342
| Re: Cms/panhard issue
Ok so what you are saying is that you don't have enough shock travel?
|
02-11-2014, 01:05 PM | #3 |
Quarry Creeper Join Date: Dec 2008 Location: Santa Mira
Posts: 342
| Re: Cms/panhard issue
Perhaps you could try if you have not yet done so is flipping your lower shock mount right side up to give you a little more height.
|
02-11-2014, 01:09 PM | #4 |
Quarry Creeper Join Date: Jun 2013 Location: South jersey
Posts: 265
| Re: Cms/panhard issue
Pictures will do wonders for help. Post them up and we can help a little better
|
02-11-2014, 01:30 PM | #5 |
RCC Addict Join Date: Mar 2009 Location: Interior BC
Posts: 1,786
| Re: Cms/panhard issue
are the panhard bar and the drag link of the exact same length?
|
02-11-2014, 02:04 PM | #6 |
Rock Stacker Join Date: Jan 2014 Location: Duluth, MN
Posts: 91
| Re: Cms/panhard issue
Impossible to say much without pictures man. Without pictures it could equally be assumed you have tiny crappy shocks or hooked something up incorrectly with the pan hard kit
|
02-11-2014, 02:41 PM | #7 |
RCC Addict Join Date: Mar 2009 Location: Interior BC
Posts: 1,786
| Re: Cms/panhard issue
make sure all four corners are the same! x2 100mm on front x2 90mm on rear not so good... |
02-11-2014, 06:23 PM | #8 |
RCC Addict Join Date: Nov 2009 Location: cleveland,Tn
Posts: 1,331
| Re: Cms/panhard issue
I will get pics up just been at work sorry guys I am usually on top of pics with my post .
|
02-11-2014, 08:40 PM | #9 |
I wanna be Dave Join Date: Dec 2012 Location: idaho
Posts: 2,658
| Re: Cms/panhard issue
Seems to be the same cms issue. It bottom out going straight down but flex okay. Cms kits seem to made to work okay on most rigs but end up being not the greatest. Would take a custom set up for the cms to work properly. Drag link and pan bent and placed to clear axle components |
02-11-2014, 10:00 PM | #10 |
RCC Addict Join Date: Nov 2009 Location: cleveland,Tn
Posts: 1,331
| Re: Cms/panhard issue
on my last wraith i had the same set-up except for the proline slash shocks i was running stock wraith shocks and had plenty of travel and clearance . currently i have about 2 inches of travel . i had not thought of flipping my lower link/shock mounts over . here is some pics : this is with a pair of lexan scissors to show how much space is between the upper link mount and the rod end . |
02-12-2014, 05:27 AM | #11 |
Quarry Creeper Join Date: Jun 2013 Location: South jersey
Posts: 265
| Re: Cms/panhard issue
I am assuming you have the battery and most of your electronics up front? Are those slash front shocks? I had clearance issues on mine when I had the lower shock mounts flipped for a lower stance. I flipped the fronts to normal position and the rears to lower it and it has great forward bite and is not top heavy like stock setup. Give it a shot!
|
02-12-2014, 08:39 AM | #12 |
I wanna be Dave Join Date: Mar 2007 Location: roland,ar
Posts: 5,981
| Re: Cms/panhard issue
its normal... cms is scale..not performance. mine is the same way,i had to limit my shocks to keep them from slapping the servo. still crawls fine,just limited vertical travel. |
Cms/panhard issue - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
CMS w/Panhard or 4 Link F/R? | alexchen86 | General Crawlers | 1 | 05-18-2013 06:28 AM |
rc4wd CMS/Panhard | BoardN88 | Axial Wraith | 6 | 04-26-2012 01:47 AM |
vp cms/panhard | ax10tn | Axial Wraith | 22 | 02-07-2012 05:38 AM |
Why Does Level3 CMS not have a Panhard?! | alexchen86 | Axial SCX-10 | 3 | 01-11-2012 11:55 AM |
| |