RRP failed me! I was doin some light bashing with my wraith. I have a tekin sc4x 7.5t in it(love this motor!), anyways i was jumping a little ramp and next thing i knew i didnt have front wheel drive. I picked my wraith up and saw my mip driveshaft hanging and my upper driveshaft spline gone. I looked arounf the parking lot and found it with the pin still in it. This is what i found... http://img.tapatalk.com/d/13/06/02/gujamume.jpg |
Re: RRP failed me! I've see this happen before. The main reason I still run the stock drive shafts. I rather them break than my RRP one piece bottom gear. |
Re: RRP failed me! Yeah I have heard the same story!! I hope mine lasts a little longer. I am using only 2S with a Tekin RS and Redline 13.5T motor. |
Quote:
|
I'm running a Pro4 3300kv. I haven't had mine break yet. I would try to contact RRP and see if they might help you out. Sent from the foot hills of Tennessee. |
Re: RRP failed me! Got a buddy that has twisted and bent 2 of these. One of them just driving in the yard. I don't think RRP will be wanting to replace it but keep on them and they should. I know they didn't want to replace his. |
Re: RRP failed me! Or contact supershafty.com & get... http://i1321.photobucket.com/albums/...ps3c78a95e.jpg http://i1321.photobucket.com/albums/...psd9b25ba9.jpg http://i1321.photobucket.com/albums/...psd9b25ba9.jpg Chromoly Extended outputs up to 8mm!!! Broke a couple of those just like the pic shown. This trans is nearly bulletproof! |
Just imagine what would have happened to your stock diff... LOL |
Re: RRP failed me! Quote:
|
Just broke the rear. Thats a 2 pole brushless motor doing that! I was driving around in my loving room not even going fast. Just putting around and the rear shaft fell out. |
Re: RRP failed me! I piece bottom gears, meh. Get a good quality steel gear and use a better output like SuperShafty or stay with a stock output. |
Quote:
|
Re: RRP failed me! SuperShafty or the outputs from Crawler Innovation. I have the outputs from Crawler Innovations put up against a 6900kv Castle 4 pole motor and a Mamba Max Pro and MIP driveshafts. My Wraith probably weighs about 8bs with a 5000mah 40C 2S lipo in it. There's no telling how many times I've "bumped" a rock trail and doing a full throttle landing. |
Why would you want to run Any output shaft with a hole in it? I know it was made that way, but anytime you put a 2.8mm hole in a 5mm shaft your asking for trouble. Just get the Scx10 Rpp outdrive without the hole, locktite a 3mm setscrew in there and never worry about it again. Just my $0.02........ |
Re: RRP failed me! Quote:
It might sound like I've had wayyyyy too many tonight (I have had a few) :oops::oops: |
Re: RRP failed me! Quote:
Beefy = better I like a through hole design, no chance of driveshafts spinning or popping. |
I got it back sometime ago. But it looked like to me, and alex chen that they had welded the ended back, re lathed it, and drilled back |
Re: RRP failed me! Quote:
|
When i get done repairing a busted water pipe. I should be getting my pro4 HD Tuesday, or wendsday. I'll have my tranny out for that |
Quote:
|
All times are GMT -6. The time now is 11:26 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com