New project XR10

[angel_megane]

Originally Posted by FLOKI-81

There is always some hitec servo for sale at the classified section,,,
and alot off other goodies..

Hellou my friend

Thanks for your comments and help
I'll think about what you've told me

[FLOKI-81]

Originally Posted by angel_megane

Hellou my friend

Thanks for your comments and help
I'll think about what you've told me

I would have looked out for a hitec 7950,, same as I got,, only I paid 149,99$ fot it on Amain...
I`ve seen 7950 all the way down in the 40-50$ range on the classified pages..
And alot off vanquish stuff for the xr10 from time too time..

[angel_megane]

First test ... and the first question ...
Drives and motors with brushes and emi are GT3B
The rear axle when you have difficulty loses traction ... and forward smoothly .... this is normal ??

[FLOKI-81]

there is a hitec 7955 on the for sale sites right now,came yesterday...
70$,, I bet you can talk it down to 60$....

[angel_megane]

I see a hitec 7954 in spain

Now ..resolve the problem of traction lost

[angel_megane]

This is hv servo

Is my problem
First test ... and the first question ...
Drives and motors with brushes and emi are GT3B
The rear axle when you have difficulty loses traction ... and forward smoothly .... this is normal ??

[FLOKI-81]

Originally Posted by angel_megane

This is hv servo

Is my problem
First test ... and the first question ...
Drives and motors with brushes and emi are GT3B
The rear axle when you have difficulty loses traction ... and forward smoothly .... this is normal ??

do you have the same motors front and rear,,,

[angel_megane]

Y es...

[winnerone23]

Originally Posted by FLOKI-81

My crawlermentor and best friend bought a CVD from dlux with 70* steering,,
the steering was awsome,,but only for like 3 days before it broke,
Dlux have most likely cutted away to mutch off the CVD and it is a small and cheep item for dlux,, he takes 12$ for the job that takes about 20minutes,
And my friend contacted dlux and said that it broke after only 3 days on the rocks,,and my mentor is a Turtle on the rocks and I am the rabbit,he runs 40T pullers flow from HH and I run 35T tourqemaster pro motors.
I am a mutch more agressive pilot than my friend,,
and he complained about the lack off quality off the product he bought from dlux,,
and dlux takes no responsebillity and blames axial for some weakness in the one particular CVD..
My friend had plans to buy axels from dlux this winter but dlux wont sell my friend some superlites because off an argument about an item that cost 45$..
and the axels would have made dlux about 800$ more $$$$$$$$$$$$

I think you should have more knowledge before throwing ur thoughts around, son..
I can personally explain ur failure in making this post, without saying a word, but I think you need it explained, to understand...

If Anything, Dlux doesn't take enough material off! Erik takes just the right amount off to get 70°.. Even tho, NOBODY on this forum can even get 70° of steering!
Unless ur egresor and make a double jointed vvd style cvd.. He even backed off to 67° cause the con's out weighed the pro's.

Now, maybe you know what a Super 300 HD looks like? I do, and I make my axial uni's look like them! Cutting/grinding 3 times as much material as Dlux does..

I HAVE NEVER HAD ONE BREAK!
not at the uni anyways..
I have had the stub shafts break off at the hex pin. Then again, that was in my wraith with a Pro4 4000kv brushless motors on 4s.. They don't take mega jumps, nose dives on full throttle, out slamming into rocks at 26mph!

If ur friend got a bad uni, then he got a bad uni.. Plain and simple!
It's not Dlux fault or his place to replace Axial's bad product..

So maybe next time, you should get ur facts together before posting all over the forum..
Cause vendor's see ur posts, like this one, and they don't want you to have there products! It's bad for business and hurts there sales more so then ur one set of axles!

[winnerone23]

And here's a pic of mine dremeled to how I do them.

[FLOKI-81]

Originally Posted by winnerone23

And here's a pic of mine dremeled to how I do them.

Mine look just the same,,,only I did most off the work by hand with a file..
I measured my steering to about 63*,,,,
More than enough
The rest takes the dig care off,,

[winnerone23]

So if ur's look just the same, how can you post that "Dlux must have cutted away to mutch off the CVD"???

You can see that mine, and ur's (if they are done the same as mine) have Way more material taken off of them..

[angel_megane]

Hi guys...
There are peace!!!
In the forums will misunderstand many things

I'm still waiting for my carbon fiber .... the chasis is now designed!!!
Read more about the servos and researching my problems traction.

[angel_megane]

22kg forma servo is enough
I will not compete...

[FLOKI-81]

I like peace...
Wont continiue my argument,,, I rest my case,,,
OKAY,,, PEACE??
I wont be so dissliked her on rcc that I wont be able to purchase anything because I stood up for a friend off mine..
He can discuss this case untill he is blue,,,,
I dont care,, Rcc is my Bible and Religion,, dont want to upset the gods,, he he he..
I just wanna be able to can have a okay dialog between vendor and purchaser,,in this case ME!!!

[angel_megane]

Hi guys...

Now, I have de carbón fiber - kevlar and
new servo.. powerhd stormer 3
Power HD - HuiDa RC International INC.STORM-3