08-17-2015, 07:31 PM | #1 |
Newbie Join Date: Feb 2015 Location: Boston
Posts: 28
| Issue with the RPM arms
So I just installed the RPM arms on the Yeti and noticed the stock hinge pins (3x35mm button head) were not long enough to secure it so I went with the 3x40mm cap head screws based on another thread on this forum. With this setup the wheel tends to get stuck on the nut or cap head when turning. Any downsides to using a longer hub upfront? I have an extra set of Axial stock hubs. |
Sponsored Links | |
08-17-2015, 07:32 PM | #2 |
I wanna be Dave Join Date: Jul 2013 Location: Minneapolis
Posts: 5,202
| Re: Issue with the RPM arms
On the castor block? What wheel?
|
08-17-2015, 07:34 PM | #3 |
Newbie Join Date: Feb 2015 Location: Boston
Posts: 28
| Re: Issue with the RPM arms
Stock wheels, it's getting stuck on the 3x40mm screw and nut where the caster block connects to the arms.
|
08-17-2015, 11:03 PM | #4 |
I wanna be Dave Join Date: Jul 2013 Location: Minneapolis
Posts: 5,202
| Re: Issue with the RPM arms
Ahh I see. Those wheels don't have a lot of clearance with those big rings. Sent from my VS986 using Tapatalk |
08-18-2015, 04:59 AM | #5 |
RCC Addict Join Date: Nov 2009 Location: New Wilmington, PA
Posts: 1,234
| Re: Issue with the RPM arms
Use the stock screw, I've never put a nut on the end of mine with the RPM's. Put a dab of CA glue in the arm where the threads of the screw thread into if you want extra security. |
08-18-2015, 10:33 AM | #6 |
I wanna be Dave Join Date: Jul 2013 Location: Minneapolis
Posts: 5,202
| Re: Issue with the RPM arms
I just grabbed a really long screw I had put the nut on the back and cut the excess of the screw off. Works fine but I'm not using stock wheels. Sent from my VS986 using Tapatalk |
08-18-2015, 11:21 AM | #7 |
Quarry Creeper Join Date: Nov 2014 Location: WA
Posts: 375
| Re: Issue with the RPM arms
I used the stock screw without glue or anything. Is working great in the last 6 months. |
08-18-2015, 11:36 AM | #8 |
I wanna be Dave Join Date: Jul 2013 Location: Minneapolis
Posts: 5,202
| Re: Issue with the RPM arms
Mine were coming loose. Which is why I got a longer screw.
|
08-18-2015, 02:13 PM | #9 |
Rock Stacker Join Date: Sep 2013 Location: Wyoming
Posts: 49
| Issue with the RPM arms
Mine would come loose all the time so I replaced them with 3mm rod held in with a set screw from the bottom |
Issue with the RPM arms - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
what 3mm hingnw pinare you guys using for the rpm arms | mushroom281 | Axial Yeti | 16 | 01-08-2015 06:34 AM |
RPM Front A Arms | YETI...Set...Go!!! | Axial Yeti | 12 | 09-17-2014 09:43 AM |
Who wants RPM a-arms ??? | tklatti | Traxxas Crawlers | 3 | 05-01-2011 02:04 PM |
RPM Slash Rear A-arms | mutiny22 | Non Crawler RC's | 7 | 10-23-2008 09:28 PM |
| |