Berg/Axial Knuckle weights Brass knuckle weights. Proudly made in the U.S.A. Brass knuckle weights to attach to the steering knuckle. This weight will fit: Axial brand hi clearance knuckles VP brand Axial hi clearance knuckles VP brand Berg hi clearance knuckles VP brand Axial zero ackerman knuckles (may require light grinding) RCbros LOSI hi clearance knuckles (mild modification necessary) WILL NOT WORK WITH STOCK BERG KNUCKLES. ALL AXIAL REFERENCES ARE FOR THE AX10, NOT THE XR10. Benefits of a knuckle weight system Less rotating mass Less broken parts More wheel speed More run time per battery Serious increase in stability Sidehill, uphill, downhill Pulls out/does not get into binds like running with wheel weights Feels MUCH lighter. Feels like it climbs 1000x better Each knuckle weight is 2.4oz The weights have been tapped so extra rings can be bolted to them. Each .100 ring weighs approx .4 oz. Each .300 ring weighs approx 1.2oz. Each large diameter ring (goes around the knuckle weight) weighs approx 3.4oz. Pricing: Knuckle weight complete setup: (2) Knuckle weights, (4) extra rings and all hardware $83 (2) Knuckle weights $58 (2) Extra .100 rings with hardware $15 (2) Extra .300 rings with hardware $20 (2) Large diameter rings with hardware $20 http://www.dluxfab.com/products Wheel weight combos: A Vanquish DH wheel with 585 hubs can use .200 extra rings per side. A Vanquish SLW wheel with 475 hubs can use .500 extra rings per side. A Vanquish SLW wheel with 600 hubs can use .600 extra rings per side. A Vanquish SLW wheel with 725 hubs can use .800 extra rings per side. A stock Losi LCC/LNC cannot use any extra rings. Proline Titus wheel with about 1/32" dremel clearancing of the ribs inside the wheel can use .200 extra rings Thanks Shawn M DNA assassin AX10 offset wheel can use approx .700 extra rings Thanks ShellJeep A CKRC murdered out wheel can use .400 extra rings per side. Thanks Jslick A Motoworks (style?) wheel can use .300 extra rings per side. Thanks Jslick http://i180.photobucket.com/albums/x...ling/Berg1.jpg http://i180.photobucket.com/albums/x...ling/Berg2.jpg |
|
Looks nice!! What is the diameter and width of the knuckle weight? |
Quote:
|
Wheel Weights Will these work with Mayhem comp phattys axial wide offset and Vanquish ZA in a BTA setup? |
Quote:
Basically, I am trying to figure out if it will work with any of my 1.9 wheels. |
Quote:
As soon as I get feedback from everybody on what works I will update the thread above with more info on what wheels work with what ring combos. |
Quote:
i.d. is 1" the width will come out close to flush with the backside of the hex. |
I still have about half of the knuckle weights left. I only have enough .100 rings for one more "complete set" then I will be turning that option off until approx next week when I get more in. Also, you should only need 2- .100 rings per side, ever. After that its much better to order the .300 rings |
And gone.... I will have more .100 rings soon. |
Thanks for the ultra fast shipping. Very nice product! "thumbsup" |
So these will not work w RCBros zeroack knuckle, correct? They look real good |
Quote:
|
Quote:
I'll be ordering soon ! "thumbsup" |
Quote:
http://www.rccrawler.com/forum/team-losi-comp-crawler/301737-rcbros-hi-clearance-knuckle-weights.html |
Quote:
|
I have the knuckle weights, just no .100 rings. I should have some more .100 rings in stock next week. |
Just ordered the knuckle weights and the .300's. Who needs the little .100's anyway. :mrgreen: |
Quote:
Shipped! |
Thank you for the fast shipping and responce "thumbsup" |
All times are GMT -6. The time now is 10:01 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com