Re: **AX10/SCX10 Housing Splined Burly Tubes** Got my set yesterday Very nice looking I went to install them and I can,t get the c-hub to slide all the way on It slide till it runs out of splines inside the c-hub which leave about a 1/8th of beef tube spline showing between the caller and c-hub. I will take a picture to post when I get home |
Re: **AX10/SCX10 Housing Splined Burly Tubes** LMK what brand Chub you are using please. I'll do what I can to help. I just spot checked a few more with no bad results. We will see what we can do to get you fixed up. |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Any chance you'll make some for Wraith axles? Pretty please? ;-) |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
I will take a couple picture when I can get back down to the garage Yeah doesn't make sense to me either I'm sure it's something small |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Did you get this figured out? |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
|
Re: **AX10/SCX10 Housing Splined Burly Tubes** Just added the colors to our cart system. Hope to get pictures up when I get caught up! |
Re: **AX10/SCX10 Housing Splined Burly Tubes** So is it confirmed that for the rear you can run wraith lock outs and long side wraith shafts so track width is same as the front with the xr steering? |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Got mine started http://i1057.photobucket.com/albums/...9703aa8805.jpg |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
|
Re: **AX10/SCX10 Housing Splined Burly Tubes** The lightest option is to leave the rear axle stock and run flipped wheels in the back. |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
For the scalers and those who dont like this option, I'm sorry this is taking so long. I'm pretty sure the Wraith rear locker and XR10 long rear shaft is the ticket. However, I cannot confirm till I get some rear lockouts in hand. I just installed the XR10 rear lockout on our Burly tubes out back with XR10 rear short shafts. This combo bolts together, however is still not equal track width. |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Is it close to the same & how much wider than the stock SCX width?? Thanks for your insight. |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Can you make some that do not have the extra collar area so the splines end at the shock mount? I want the advantage of the steering without the width;-) |
Re: **AX10/SCX10 Housing Splined Burly Tubes** I put together the rear lastnight and to make the width you need burley tubes and wraith lockouts. |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
And what shafts? |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Hey Guys, If your wanting equal track width, a set of burly tubes in back is required along with wraith lockouts and XR10 rear long shafts, there are several vendors who can cut you 2 long XR10 Shafts. If you are using these for a sporty with a flat faced wheel, you can easily flip the wheel for equal track width. I am working on an option for you stock width guys, and hope to have a how-to up by the end of the week. |
Alright, for those guys wanting a 7075 burly tube but want to retain your stock width, here's what you need to do. First cut 12mm off your burly tube. http://img.tapatalk.com/d/13/12/17/muravynu.jpg Then cut your axle halves flush with the link mounts. At this point your burly tube fits right in. http://img.tapatalk.com/d/13/12/17/buheve5y.jpg You will still need to drill and tap the burly tube, but now you have a killer burly tube upgrade. http://img.tapatalk.com/d/13/12/17/y3uvymy3.jpg |
Any one have a picture compared to a stock scx10 axle and a sock wraith axle? Sent from my HTC6435LVW using Tapatalk |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
|
All times are GMT -6. The time now is 03:11 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com