Re: **AX10/SCX10 Housing Splined Burly Tubes** Ok, you modified a long set to work. Will you be offering them in the narrow style at a lesser cost since we won't be needing the extra collars and set screws?"thumbsup" |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
Quote:
|
Re: **AX10/SCX10 Housing Splined Burly Tubes** I order a set today and I don't need the collars . I'm going with the narrow setup . |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Forgive my crawler newbness. I have yet to fully understand the XR10, AX10, SCX-10, Wraith, etc etc nuances. What I have is an SCX-10 G6 and I would like to be able to index the front c-hubs in order to get proper steering knuckle angle and driveshaft angle at the same time while retaining stock width. What other parts do I need besides a set of cut burly tubes? |
Cut burly tubes, cut xr10 universals. Wraith C hubs and knuckles. Sent from my iPhone using Tapatalk |
Re: **AX10/SCX10 Housing Splined Burly Tubes** How did you manage to utilize and tighten down the grub screw's on the grip fab locker after installing the tubes? |
This version doesn't have the grub screws. It is a spool. However most guys pop a small hole in the housing Sent from my iPhone using Tapatalk |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
Thanks. That is what I did, but was not sure if that was the way others do it. "thumbsup" |
Re: **AX10/SCX10 Housing Splined Burly Tubes** couple questions 1. did you ever get the short burleys on the website (i can't find them) 2. if I use the shorter (12mm w/ no collars) do I still use wraith hubs/chubs I really really would like this option, thx for any help to go this direction. |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
I can do it though, but usually charge alittle more for the time. Yes, Wraith chubs and knuckles are still used. A XR10 Universal set will need to be cut down. "thumbsup" |
Ok thx |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
|
Re: **AX10/SCX10 Housing Splined Burly Tubes** Quote:
Did you ever get these up yet.I just check web I didnt see them.thanks |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Sorry if it's been posted already, just didn't see it. What is the weight of both tubes? |
Quote:
Correct, just flattening the ends with a dremel tool. Sent from my iPhone using Tapatalk |
Quote:
Sorry for the delay, will get this done tonight! Sent from my iPhone using Tapatalk |
Quote:
http://img.tapatalk.com/d/14/01/24/9equheqa.jpg Sent from my iPhone using Tapatalk |
Re: **AX10/SCX10 Housing Splined Burly Tubes** Good stuff"thumbsup" I will be ordering soon8) |
Mine were ordered earlier this week, can't wait to start the build |
Re: **AX10/SCX10 Housing Splined Burly Tubes** I'm gonna assume that I would need to run an xr steering link set to keep my axle mounted servo correct? |
All times are GMT -6. The time now is 02:06 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com