|
| LinkBack | Thread Tools | Display Modes |
06-15-2010, 08:39 PM | #1 |
Quarry Creeper Join Date: May 2010 Location: trinity
Posts: 295
| novak rooster crawler esc
hi guys i ahe a question when i plug in my battery on the truck it wants to jump seriously how do i fix this cause its really anooying an kinda odd thanks for the help zach
|
Sponsored Links | |
06-15-2010, 08:50 PM | #2 |
Newbie Join Date: Oct 2008 Location: Decatur, TN
Posts: 21
|
Did you change connectors? I accidentally mixed up the wire colors and soldered my battery leads to the motor and motor wires with a deans connector, so as soon as the plugs made contact it would jump. Hope this helps. |
06-16-2010, 06:03 PM | #3 |
Rock Crawler Join Date: Aug 2009 Location: Thomasville, NC
Posts: 904
|
Wen he plugs it in it jumps just 4 a sec!!
|
06-16-2010, 06:21 PM | #4 |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| Whats the whole set up..full electronics spread including radio,,it sounds like you need to set your end points or trim points.
|
06-16-2010, 08:02 PM | #5 |
Quarry Creeper Join Date: May 2010 Location: trinity
Posts: 295
|
it has the the rooster crawler esc a 35turn motor a hitech dx3e radio in it if you want i think the servo is a 900 series i really dont know waht it is it was lying around so i used it an im just useing nimh batts dont want to go to lipos
|
06-16-2010, 08:17 PM | #6 |
Rock Crawler Join Date: Jan 2010 Location: Arvada
Posts: 783
|
I just got a used one and mine did it also. You just need to program it to your radio. to do this....turn the radio on first, then plug the battery in, then pull full throttle on the radio and hold it there, while holding it there turn the esc on, it'll flash or beep after a second or two, then go full reverse and again it'll flash and beep, then relax to neutral position. it'll then be ready to use. it worked for mine atleast, and if my instructions are not right just look it up in the manual which if you don't have you can find online. good luck and hope this helped |
06-17-2010, 12:02 AM | #7 |
RCC Addict Join Date: Jun 2008 Location: Fresno
Posts: 1,464
|
re programing the esc should cure ur problems 1- turn on tx 2- while in the off position plug in ur battery into the esc 3- while in the off position hold down the programing button 4- while holding doen the programing button turn on the esc 5- release the programing button after the red light goes on 6- pull throttle to "full- forward" position until solid green light goes on 7- pull throttle to "full - brake/ reverse" position until esc blinks green 8- return to neutral position (light should turn red) 9- crawl and have fun |
06-19-2010, 06:34 PM | #8 |
Quarry Creeper Join Date: May 2010 Location: trinity
Posts: 295
|
thanks only problem it no longer has the on off switch on it it kept breaking off so i just soldered the wires together is there a way to do it with out haveing the switch on it thanks
|
06-19-2010, 08:29 PM | #9 |
Rock Crawler Join Date: Jan 2008 Location: Calgary Crawlers, Alberta, Canada
Posts: 617
|
Just hold the button down while plugging in the battery, that does the same as using the switch.
|
| |