02-04-2012, 11:10 AM | #1 |
Quarry Creeper Join Date: Jul 2009 Location: Back from vacation!!!
Posts: 356
| AE-2 Set-Up help.
Recieved a new AE-2 ESC and cannot get it to program. All I get are rapid-flashing green light and solid red. I'm following axials instructions here- Axial AE-2 ESC Set-up and Programming Trim neutral- AX-3 T/X. Did the reversing-switch, no help. Steering works. I am not using a Li-Po at this time . This is not a new-build. It's my sons running Honcho that had an AE-1 in it, and we want to go to LiPos. Last edited by ridepate; 02-04-2012 at 11:28 AM. |
Sponsored Links | |
02-04-2012, 11:19 AM | #2 |
I wanna be Dave Join Date: Dec 2009 Location: San Francisco
Posts: 2,236
| Re: AE-2 Set-Up help.
Does it start to go into calibration or not? The only thing I can think of is if you TX has throttle end points make sure they are maxed out, other than that it is a very straight forward process and hard to screw up. You could try plugging it into the steering channel and see if that helps, again trim at 0 and end points maxed out. |
02-04-2012, 11:37 AM | #3 |
Quarry Creeper Join Date: Jul 2009 Location: Back from vacation!!!
Posts: 356
| Re: AE-2 Set-Up help.
No EPA on this transmitter for throttle. "Does it start to go into calibration or not?" It just goes ring-a-ling through the motor when I turn on the switch, at the inital turn-on, then all I get is silence with the green led flashing rapidly and the red solid. I re-installed the AE-1 just to check and it works fine. |
02-04-2012, 11:45 AM | #4 |
Rock Stacker Join Date: Apr 2011 Location: Helper, UTAH
Posts: 79
| Re: AE-2 Set-Up help.
Is the esc cable plugged into the receiver backwards?
|
02-04-2012, 11:59 AM | #5 |
Quarry Creeper Join Date: Jul 2009 Location: Back from vacation!!!
Posts: 356
| Re: AE-2 Set-Up help. |
02-04-2012, 12:52 PM | #6 |
Rock Stacker Join Date: Apr 2011 Location: Helper, UTAH
Posts: 79
| Re: AE-2 Set-Up help. |
02-04-2012, 01:32 PM | #7 |
Quarry Creeper Join Date: Jul 2009 Location: Back from vacation!!!
Posts: 356
| Re: AE-2 Set-Up help.
O.K this is wierd..... If I cycle the steering 20 times or so , sometimes it will go into programming mode, acknowlege full throttle, go to red, acknowledge reverse, give me done beeps and go silent. Then when I touch the throttle, nothing, the green starts flashing.. and this is with it plugged in properly.
Last edited by ridepate; 02-04-2012 at 01:35 PM. |
02-04-2012, 01:36 PM | #8 |
Rock Crawler Join Date: Nov 2009 Location: poteau
Posts: 996
| Re: AE-2 Set-Up help.
did you bind the radio to the reciever?
|
02-04-2012, 01:41 PM | #9 |
Quarry Creeper Join Date: Jul 2009 Location: Back from vacation!!!
Posts: 356
| Re: AE-2 Set-Up help. |
02-04-2012, 01:47 PM | #10 |
Rock Crawler Join Date: Nov 2009 Location: poteau
Posts: 996
| Re: AE-2 Set-Up help.
when i switched over to the mmp, my radio lost it's bind. that's why i asked. anyway, are you running lipo? if not, did you turn off the auto lipo cutoff on the esc? could be that the voltage is to low and the auto lipo cutoff is kicking in. another thing i had to do was get about 5 feet away from the rig and have my daughter turn it on while i held the transmitter. for some reason if i tried to do it myself it wouldn't go into cal mode. transmitter to close i guess.
|
02-04-2012, 02:08 PM | #11 | |
Quarry Creeper Join Date: Jul 2009 Location: Back from vacation!!!
Posts: 356
| Re: AE-2 Set-Up help. Quote:
But why it will kick-in to program-mode when I cycle the steering is plain strange.. | |
02-04-2012, 02:26 PM | #12 |
Quarry Creeper Join Date: Jul 2009 Location: Back from vacation!!!
Posts: 356
| Re: AE-2 Set-Up help.
Suggestion of the day winner.....................Drum-Roll...................... HogHead!!!!!!!!!! I was standing too close. Got my son to pin it and stand 10 feet away...........DONE!!! Thanks guys for all the help. I was feeling knida stoopid. I knew I knew what I was doing......... |
02-05-2012, 02:16 PM | #13 |
I wanna be Dave Join Date: Jan 2012 Location: CANADA
Posts: 2,648
| Re: AE-2 Set-Up help.
Weird but good to know the solution to your problem. I am getting my first AE-2 ESC for my new Axial Wraith kit soon and that tip will come in handy if I have similar issues. I am very new to all this RC Crawling and look forward to my first Axial build.
|
AE-2 Set-Up help. - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
~TSS~ GIVEAWAY! Ultimate Set Screw 3mm Set! | STANG KILLA SS | General Crawlers | 78 | 09-10-2011 07:40 PM |
Would I need 2 sets of rear wheels or 1 set of rear and 1 set of front?!? | FFRCJosh | Tires and Wheels | 10 | 03-01-2006 08:19 PM |
| |