RCCrawler Forums - cogging with tekin 13.5t?

RCCrawler Forums (http://www.rccrawler.com/forum/)

- Electronics (http://www.rccrawler.com/forum/electronics/)

- - cogging with tekin 13.5t? (http://www.rccrawler.com/forum/electronics/451602-cogging-tekin-13-5t.html)

SwampDawg

07-02-2013 11:44 AM

cogging with tekin 13.5t?

i had this issue with my tekin 13.5t redline and swapped it out with a brushed type. Thing is....i kinda want my brushless back! lol

problem i was having was cogging and even had purchased a new sensor wire with failed success. Using a MMP and 58/12t setup (32p)
there is no binding and im also using a 5300mah 2s lipo for this.

any ideas?

Ty@Tekin

07-02-2013 01:29 PM

Re: cogging with tekin 13.5t?

Has the 13.5 ever been wet? It may need a new sensor PCB. If you have a Tekin ESC you can use the sensor checker feature to see if they are operating correctly.

k7zpj

07-02-2013 01:31 PM

Re: cogging with tekin 13.5t?

Did you have your MMP set for Smart Sense mode or Sensored Only mode?

SwampDawg

07-02-2013 01:36 PM

Re: cogging with tekin 13.5t?

Quote:

Originally Posted by Ty@Tekin (Post 4383225)

Has the 13.5 ever been wet? It may need a new sensor PCB. If you have a Tekin ESC you can use the sensor checker feature to see if they are operating correctly.

wet a few times that i can remember and i have the MMP ESC.

SwampDawg

07-02-2013 01:36 PM

Re: cogging with tekin 13.5t?

Quote:

Originally Posted by k7zpj (Post 4383231)

Did you have your MMP set for Smart Sense mode or Sensored Only mode?

now that you mention this....i cant remember what i have this set for? i take a look, but what is it supposed to be at? "thumbsup"

Ty@Tekin

07-02-2013 01:37 PM

Re: cogging with tekin 13.5t?

Quote:

Originally Posted by SwampDawg (Post 4383233)

wet a few times that i can remember and i have the MMP ESC.

Has it been treated with anything to make it water resistant?

SwampDawg

07-02-2013 01:42 PM

Re: cogging with tekin 13.5t?

Quote:

Originally Posted by Ty@Tekin (Post 4383238)

Has it been treated with anything to make it water resistant?

nope, i popped the end cap off once just to have a look and it seemed ok?

k7zpj

07-02-2013 01:48 PM

Re: cogging with tekin 13.5t?

Quote:

Originally Posted by SwampDawg (Post 4383236)

now that you mention this....i cant remember what i have this set for? i take a look, but what is it supposed to be at? "thumbsup"

It should be set to Smart Sense mode.

SwampDawg

07-02-2013 01:55 PM

Re: cogging with tekin 13.5t?

Quote:

Originally Posted by k7zpj (Post 4383245)

It should be set to Smart Sense mode.

right on!
ill make sure of it, thanks again! "thumbsup"

Fishmaxx

07-02-2013 03:15 PM

Re: cogging with tekin 13.5t?

Quote:

Originally Posted by Ty@Tekin (Post 4383238)

Has it been treated with anything to make it water resistant?

I have similar problem.

Yes Corrosion X

What is the fix/repair?

rooster72

07-05-2014 03:04 PM

Re: cogging with tekin 13.5t?

I also have the same gogging problem. Yes corrosion x

rooster72

07-05-2014 03:06 PM

Re: cogging with tekin 13.5t?

I mean cogging.

sam63

07-05-2014 03:25 PM

Re: cogging with tekin 13.5t?

Gearing lower will help. I gear as low as I can, 93/12, and it runs super smooth. With the 32p you should be able to fit 66/10, but don't quote me, its been awhile. The lower gearing will help your drag brake too. Esc settings would be the next thing to look at. With the lower gearing you should think about running 3s or even 4s to get your wheel speed back.

Good luck, getting a brushless dialed for crawling can be tricky.

mark32

07-05-2014 06:40 PM

Re: cogging with tekin 13.5t?

i run 64/9 on my 11 pound rig on 4s it screams when i first set it up i ran 12 60 and it cogged like crazy

All times are GMT -6. The time now is 07:59 AM.