RCCrawler Forums

RCCrawler Forums (http://www.rccrawler.com/forum/)
-   Electronics (http://www.rccrawler.com/forum/electronics/)
-   -   CC Sidewinder 2 SV2 arming (http://www.rccrawler.com/forum/electronics/614088-cc-sidewinder-2-sv2-arming.html)

Thorsteenster 12-21-2019 11:39 AM

CC Sidewinder 2 SV2 arming
 
Need someone to confirm the arming process, can't find an online manual. BOOO to Castle!
I got it used on the cheap from Ebay, dude had more than 100 of em.
Any who, I connected everything and go to arm, holding full throttle works, but then holding full reverse seems to fail.
If I let trigger go to neutral after full throttle, it semi-arms and will run for a few seconds.
I've already requested a return, but figured I'd see if anyone here has suggestions.

mikemcE 12-21-2019 12:23 PM

Re: CC Sidewinder 2 SV2 arming
 
Did you calibrate it to your rx/rc ?

Look at the leds. Green is forward , Red is reverse, yellow is neutral


Hang up and Drive

jaymann 12-21-2019 12:25 PM

Re: CC Sidewinder 2 SV2 arming
 
Try reversing the ch.I had to do that on one of my mmp's.



Sent from my SM-G930W8 using Tapatalk

Thorsteenster 12-21-2019 12:40 PM

Re: CC Sidewinder 2 SV2 arming
 
Sorry, I meant calibrate, not arming.
When I try to calibrate, forward goes as expected, but then reverse led goes red and starts blinking red then never arms.
I'll try reversing.
Just tried with throttle reversed, no difference.

jaymann 12-21-2019 12:51 PM

Re: CC Sidewinder 2 SV2 arming
 
Also check the firmware.
http://support.castlecreations.com/t...support-videos.
May need a update?if it's used there may be settings for racing=no reverse.
Although it running and then stopping is odd.
Maybe a internal bec issue


Sent from my SM-G930W8 using Tapatalk

ferp420 12-21-2019 12:56 PM

Re: CC Sidewinder 2 SV2 arming
 
try the castle link adaptor and plug it in to your computer to program the esc

your radio might be in some kind of programing mode also look up its programing procedure

it could be the trim on the controler isent happy try different trim settings

Thorsteenster 12-21-2019 01:07 PM

Re: CC Sidewinder 2 SV2 arming
 
I don't have the Castle Link, but I was able to get it to calibrate and pulling the trigger the motor spins for a second then stops and the ESCs LEDs blink.
I only have two BL motors, both outrunners and same thing happens with both.
I think it's a bum ESC and I'm not going to buy a Castle Link to verify.
I miss my 1st gen Mamba, it had a mini USB port on board.

Thorsteenster 12-21-2019 02:42 PM

Re: CC Sidewinder 2 SV2 arming
 
I had been using a NiMH battery, decided to try a LiPo and worked just fine.
Ordering a Castle Link now.
Thanks guys!
In case anyone's interested:
https://www.ebay.com/itm/Castle-Crea...72.m2749.l2649

jaymann 12-21-2019 06:16 PM

Re: CC Sidewinder 2 SV2 arming
 
Exellent news.

Sent from my SM-G930W8 using Tapatalk


All times are GMT -6. The time now is 06:33 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com