2mtech's La BOMba Stop...BOMba time!! Build Details: Kit: Gmade GS-02 BOM Motor: HH Trailmaster Sport 540 35t brushed ESC: Hobbywing Quicrun WP1080 Servo: DS3218 20kg Rx: Spectrum SR310 Paint: Duratrax competition orange Duratrax metallic black Duratrax basic black Upgrades: Steel balls SSD silver 5-slot steel wheels SSD scale hubs Mods: new2rocks spread (rear lower link mount relocation) Velcro front body mount It starts with this: https://farm2.staticflickr.com/1935/...89cf08c2_b.jpg And happens here: https://farm2.staticflickr.com/1927/...26fdbac8_b.jpg |
Re: 2mtech's La BOMba Starts out with diffs. Instructions are clear and simple to follow, hardware for each step is listed with 1:1 illustrations so you don't screw too long. https://farm2.staticflickr.com/1916/...f54fd31d_b.jpg Axles were very non-RC3WD (they fit together well). As others have mentioned, rotation was a bit "crunchy", as in not smooth & silent. 50 revolutions with a hex driver as a lever smoothed them out considerably. https://farm2.staticflickr.com/1906/...2e1d7e33_b.jpg https://farm2.staticflickr.com/1970/...d92fd051_b.jpg On to the tranny. Contrasting the axles, rotation of the transmission was glossy smooth and whisper quiet. Note that the printed manual omits grease application indicators on the gears, as in other places (steps 15, 25, 36, 37 and 38 ). Use grease. https://farm2.staticflickr.com/1966/...c1fed870_b.jpg Again as others have done, I skipped from step 19 to step 25 and assembled both halves of the transmission to avoid having greased gears lying around while I built links. This will require opening the next parts bag. Assembly of the two halves was slightly problematic and took a bit of effort to snap together, particularly under the "clamps". https://farm2.staticflickr.com/1918/...75c76160_b.jpg https://farm2.staticflickr.com/1907/...5733268a_b.jpg Now to post some links. I appreciate that the similarly sized rear links had notches on two to easily distinguish them. https://farm2.staticflickr.com/1939/...59252b37_b.jpg First full build I've done since I got the Tekno multi tool...will never build without one again! "thumbsup" |
Re: 2mtech's La BOMba Next up: Battery box and servo mount. https://farm2.staticflickr.com/1942/...191fc443_b.jpg https://farm2.staticflickr.com/1955/...75f80b6d_b.jpg Because of clearance I used the supplied servo horn. https://farm2.staticflickr.com/1925/...778e802a_b.jpg Frame assembly next. As typical, installed everything to one side and then installed the other side. Little bit of a balancing act as some parts are not actually mounted to the frame yet but need to be in place... Fun fact: Some of this part I did by lantern and headlight as Hurricane Florence had knocked out the electricity! https://farm2.staticflickr.com/1905/...cc463788_b.jpg https://farm2.staticflickr.com/1936/...9e29bc55_b.jpg https://farm2.staticflickr.com/1934/...cf531a3a_b.jpg https://farm2.staticflickr.com/1933/...f10ba7d3_b.jpg https://farm2.staticflickr.com/1958/...bf8300d3_b.jpg https://farm2.staticflickr.com/1966/...08eb8aec_b.jpg |
Re: 2mtech's La BOMba Link installation next. I was in rare build form here, boy...managed to install them wrong three times. DOH! https://farm2.staticflickr.com/1936/...b781cd0b_b.jpg https://farm2.staticflickr.com/1943/...c68dc322_b.jpg Then time to mount the motor. Kind of a unique (to me at least) way of mounting a motor where pinion mesh is pre-set depending on its number of teeth. Every pair of holes in the mount is marked for a corresponding pinion tooth count. I used the supplied 12t pinion, and surprisingly the mesh was pretty darn close to where I would have set it anyway if on a normal eccentric. https://farm2.staticflickr.com/1934/...d2fe62ee_b.jpg https://farm2.staticflickr.com/1905/...813e5c44_b.jpg Spur cover was a tight fit...nothing getting in there! https://farm2.staticflickr.com/1966/...cf02f8c5_b.jpg Then my all time favorite part <sigh>...shocks. :roll: These went every bit as well as every other set of shocks I've done, so not stellar. Ignore the redneck engineered shock stand, it works. Pro tip: Install the lower rod ends (steps 34 & 35) before trying to bleed (step 33). https://farm2.staticflickr.com/1940/...8be987b8_b.jpg I emailed Gmade that they had screwed up the kit because two of the shocks were WAY shorter than the others. They never answered... :lmao:. The shorter ones are because cantilever but it messes with the senses at first! Tekno tool FTMFW! https://farm2.staticflickr.com/1977/...80bd8967_b.jpg Driveshaft time: https://farm2.staticflickr.com/1971/...8fc7a0e9_b.jpg https://farm2.staticflickr.com/1953/...29402444_b.jpg |
Re: 2mtech's La BOMba Step 39 is where the wider link spread suggested by new2rocks takes place. It outboards the lower links as well as the cantilever mount struts. I added 8mm spacers in the now open space between flanges to add rigidity. https://farm2.staticflickr.com/1925/...5f2fc2cc_b.jpg https://farm2.staticflickr.com/1952/...fd016bbe_b.jpg Then in goes the front axle with all associated connections... https://farm2.staticflickr.com/1936/...64cc0649_b.jpg https://farm2.staticflickr.com/1938/...1d21047b_b.jpg Then on to electronics. Almost functional!! https://farm2.staticflickr.com/1944/...3b0ac393_b.jpg Top of the transmission had a convenient flat spot to mount the power switch for the ESC. Mounting of the rx was different...attached to the lid instead of the bottom of the receiver box. After thinking about it, it made sense for drainage, although the box is o-ringed and appears to be pretty tightly sealed. https://farm2.staticflickr.com/1936/...a2615fb2_b.jpg Then...hweels and tahrs! Stock meats didn't impress me at first, but after scrubbing the mold release off they were stickier than I expected so I decided to try them. I mean, it would look silly if every rig I have had Hyrax tires on them, right? ;-) https://farm2.staticflickr.com/1937/...8f7af7f1_b.jpg Almost there now! "thumbsup" |
Re: 2mtech's La BOMba I just ordered the same wheels for mine. Prefect match for the body imo! |
Re: 2mtech's La BOMba As usual, I had a paint layout visualized that sort of materialized. It came out...well, pretty good. But it was obviously missing...something. https://farm2.staticflickr.com/1920/...a475a406_b.jpg Fast forward a bunch. Pretty much finished now. After striping it I almost pulled the decals back off the sides, but I let it sit a couple days and kept looking at it. Finally decided they could stay. My Bomber is the only rig I have that has graphics on it so I figured what the heck. https://farm2.staticflickr.com/1917/...c5cc66f7_b.jpg https://farm2.staticflickr.com/1946/...1a97b262_b.jpg https://farm2.staticflickr.com/1969/...3cc7ce26_b.jpg https://farm2.staticflickr.com/1966/...0591edfb_b.jpg Really digging on these SSD vintage wheels! https://farm2.staticflickr.com/1964/...5f5f3cbb_b.jpg Just have to make the front velcro body mount, repaint the gaffed fuel cell and install it, and mount the spare and it'll be ready for all the fun events coming up next month!! |
Re: 2mtech's La BOMba Man, yours came out great! I'm still at building shocks, which I plan on doing tonight. I also plan to stripe mine... but plan to do it differently from how you did yours. Nevertheless, it came out looking fantastic. |
Re: 2mtech's La BOMba Great looking truck! The more I see them the more I want one. So were 2 of your shocks the incorrect length or were they short because of the cantilever suspension on the rear? |
Re: 2mtech's La BOMba Quote:
|
Re: 2mtech's La BOMba Looking pretty sweet! I was initially not too enamored by the BOM's looks, but it has sort of grown on me. Which is worrying because I must NOT buy it, I barely drive the Komodo and GOM as it is! |
Re: 2mtech's La BOMba Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
|
Re: 2mtech's La BOMba Really digging the wheels and the color scheme "thumbsup". I had a similar idea for paint on mine, orange seems to be a popular choice. Any plans for dressing up the cage with accessories or lights? |
Re: 2mtech's La BOMba Great job on the body....I have to say, I'm pretty impressed with my BOM's performance. |
Re: 2mtech's La BOMba Quote:
Quote:
|
Re: 2mtech's La BOMba Nice build!! I like orange for my trucks as they can been seen easily if they disappear into the brush I am struggling to not scratch the itch seeing these BOM builds. Must not buy (yet)...... |
Re: 2mtech's La BOMba Quote:
Do IT!! BUY ONE NOW!!!:mrgreen: |
Re: 2mtech's La BOMba No!!!!!!!!!!!!!!!!!!!!! Stop it !!!!!!!!!!!!!!! |
Re: 2mtech's La BOMba Quote:
You must buy one! Your fellow countryman said so, and he has a really nice one so you must listen! :lmao: |
Re: 2mtech's La BOMba Finished my SOP body mount (only one this time) using a plastic rectangle drilled and shoo goo'd to the body posts, post ends trimmed down, topped with good old industrial strength Velcro. This addition had the bonus benefit of adding some much needed rigidity to the front shock hoops while still allowing sufficient battery space. https://farm2.staticflickr.com/1941/...cacc2895_b.jpg With the front thusly mounted, I wasn't real thrilled with the rear hinge posts staying floating per the manual, so I drilled them through and used the last two M3 x 10 round head screws from the hardware as mount screws. https://farm2.staticflickr.com/1928/...f6065a75_b.jpg Stuffed in the back-to-black fuel cell (long story) and added an MST donut spare. Might have to hit up SSD about spares. Or whaddya think, OSRC, two more guys run these we'll throw in on a set? "thumbsup" https://farm2.staticflickr.com/1976/...5b4ac8d5_b.jpg That'll about do it until it's been trailed a time or two. I'll likely put a light bar on it...I'm DONE with fiddly LEDs and light controllers that never work, or for very long. There are some native mount points on top of the cage behind the cab and in the front bumper begging for something... |
All times are GMT -6. The time now is 06:11 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com