Locked Up RC - FI Spool http://www.lockeduprc.net/images/logo/logo3dark.png I'm thrilled to present our latest creation, our "FI Spool". http://www.lockeduprc.net/drivetrain/spool/2.jpg A lot of time and effort has gone into bringing you this spool and we think it will be a real no nonsense winner. Medium weight (1 oz) Super durable hardened steel Compatible with Axial and HPI gear sets We designed this spool to be a super tight fit ... because nobody likes slop. We also designed them to be f*****g indestructible. :mrgreen: Order here & enjoy: Locked up RC - FI Spool "thumbsup""thumbsup""thumbsup" |
Re: Locked Up RC - FI Spool Oh man! Those are sweet! Better go count up how many I need now"thumbsup" |
Re: Locked Up RC - FI Spool Very nice and thats a vvery cool deal your offering! |
Come on paypal funds! I see a few HR spools hitting the for sale section... :cool: Very cool product. |
Re: Locked Up RC - FI Spool Always great to see new parts out from LOCKED UP"thumbsup""thumbsup" I was not planning on tearing my axles apart in the middle of the scale season, but for theses it is totally worth it. |
Re: Locked Up RC - FI Spool Order placed for the spools and some other scale goodies. "thumbsup" Patrick I also included a message in my order for you. Thanks, John |
Re: Locked Up RC - FI Spool Sick!! That is awesome Patrick! I will let the local guys know |
Re: Locked Up RC - FI Spool Looking good Patrick! "thumbsup" |
Re: Locked Up RC - FI Spool nice looking unit |
Re: Locked Up RC - FI Spool Mine are on the way. After the comp on sat I have another reason to tear my rig apart, I broke the 4link in the back again and broke loose the spot weld on the front bumper. First place wins don't come cheap. While those are getting fixed I can pull the axles out and get ready for the new FI Spools."thumbsup" |
Re: Locked Up RC - FI Spool Gonna be sending a set of these to Dan for the Vuckin Double Cab! http://www.rccrawler.com/forum/1-9-s...ser-build.html "thumbsup" |
Re: Locked Up RC - FI Spool Got mine yesterday. Woohoo. Now to decide whether to save these for my other 2.2 build or for my 1.9 jk project! |
Re: Locked Up RC - FI Spool Hello, I have been looking around RCC to find a new locker/spool (however you prefer to call them). I previously tried to install Hot racing lockers, but upon installation in my SCX10 (with OD and normal gear ratio HD gear), I noticed that the gear mesh between the pinion and the ring gear was just horrible (gritty). To find out if the lockers where the problem, I pulled out my trusty electronic calipers. What I have found is pretty disturbing, from the highest point of the locker to the highest part of the ring gear, without bearings installed (From the tip of where both bearings are supposed to be installed), the stock setup (stock lockers, stock ring gear) measured 24.76mm, so this was now my baseline measure. So I then measured the Hot racing locker with the overdrive gear, 24.48mm!!!! The dimensions were so off that I could move the ring gear left and right in the bearing slot! No wonder my gear mesh was off. To further my testing, I measured Hot racing locker with stock gears, 24.46mm, same problem as before. So in the meantime, I am running the stock lockers with overdrive gears in front and stock ratio HD in the back, those measure 24.81mm which is a very nice fit in the AX10 axles. Could you measure one of your lockers and gear assembly just so I can be sure that I don’t run in the same problem as with the Hot racing lockers? Thanks in advance |
Re: Locked Up RC - FI Spool Did you install the seal/spacer washer to shim the ring gear over a little bit??? TowerHobbies.com | Axial Diff Gasket 16x25x0.5mm |
Re: Locked Up RC - FI Spool The measurements were taken without gasket on the Hot racing lockers, but they are made to be used without them anyways. |
Re: Locked Up RC - FI Spool Very cool Patrick! I had been putting off buying spools for my wife's and my wraith. Now I'm glad I waited. Going to order 4 now. "thumbsup" |
Re: Locked Up RC - FI Spool Quote:
But that isn't the important measurement because the bearing will cover up the part it rides on. What you need to measure is from the face the gear touches on to the lip the bearing rides against. On my unit that is 15mm. "thumbsup" |
Re: Locked Up RC - FI Spool Do you have any feedback from people running them in the AX10 axles? Do they fit as well as in the wraith ones? Thanks |
Re: Locked Up RC - FI Spool I got my spools and they look great. I hate to be that guy but I have to say I really wish they came with the 2mm bolts that hold the ring gear on. The upgraded axial gears don't come with them and they are always the hardest to find in the screw bin. |
Re: Locked Up RC - FI Spool Quote:
"thumbsup" |
All times are GMT -6. The time now is 09:38 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com