RCCrawler Forums

RCCrawler Forums (http://www.rccrawler.com/forum/)
-   Losi Mini-Rock Crawler (http://www.rccrawler.com/forum/losi-mini-rock-crawler/)
-   -   Axle shaft dimensions for MRC (http://www.rccrawler.com/forum/losi-mini-rock-crawler/591801-axle-shaft-dimensions-mrc.html)

Huumori 11-14-2017 12:21 AM
Axle shaft dimensions for MRC
 
Hi,

What is mrc thickness of axle shafts?
I need dimension of that part what goes through
Bearings at c-hub and knuckles?

I have mod hr-racing knuckles and c-hubs to my rc4wd 1/18 gelander but i still need some cvd's to it.

Lähetetty minun ONEPLUS A3003 laitteesta Tapatalkilla

chino63 11-15-2017 05:25 PM
Re: Axle shaft dimensions for MRC
 
All the axle bearings are 4mm I.D.
However the inner axle shafts neck down to 3mm but as for where the axle is in the bearings, 4mm.

Huumori 11-15-2017 09:10 PM
Re: Axle shaft dimensions for MRC
 
Ok thanks!
Then it would be possible to use. Next problem is where i can get mrc cvd's...

Rc4wd's yota 2 axle I.D is a bit over 3mm, so if i try to drill bigger for 4mm axles it would crack.

Bearings is to easy change. So where i can get mrc cvd's :D?

Lähetetty minun ONEPLUS A3003 laitteesta Tapatalkilla

chino63 11-16-2017 09:45 AM
Re: Axle shaft dimensions for MRC
 
Quote:
Originally Posted by Huumori (Post 5767455)
Ok thanks!
Then it would be possible to use. Next problem is where i can get mrc cvd's...

Rc4wd's yota 2 axle I.D is a bit over 3mm, so if i try to drill bigger for 4mm axles it would crack.

Bearings is to easy change. So where i can get mrc cvd's :D?

Lähetetty minun ONEPLUS A3003 laitteesta Tapatalkilla
MRC CVD's are going to be hard to find since they don't make them any more. I see them pop up on ebay once in a while but honestly, they are pretty weak. I've broken several from MIP, 3racing and some other cheap brand.

I have modified Losi Comp Crawler CVD's in all my mini axles. They need to be modified to fit. Turn down to 4mm and cut the two flats to engage the locker as well as turn down part of the stub shafts to fit the inner 4mm bearing at the knuckle.

Huumori 11-16-2017 02:11 PM
Re: Axle shaft dimensions for MRC
 
Quote:
Originally Posted by chino63 (Post 5767572)
MRC CVD's are going to be hard to find since they don't make them any more. I see them pop up on ebay once in a while but honestly, they are pretty weak. I've broken several from MIP, 3racing and some other cheap brand.

I have modified Losi Comp Crawler CVD's in all my mini axles. They need to be modified to fit. Turn down to 4mm and cut the two flats to engage the locker as well as turn down part of the stub shafts to fit the inner 4mm bearing at the knuckle.
Do you mean driveshaft LOSA3196?
And do you know does this work with hotracing MRC1908 and MRC2108?

Bearings must be 4x8?



Lähetetty minun ONEPLUS A3003 laitteesta Tapatalkilla

ElChupacabra 11-16-2017 02:37 PM
Re: Axle shaft dimensions for MRC
 
Just do the XR mod to your MRC axles and run XR Universals. You need XR/Wraith C-Hubs, Knuckles, Universals, and the appropriate bearings. You have to be willing and able to trim the XR universals to fit the MRC axle and locker. It's not hard with a grinder or dremel and a nice flat file.

https://www.shapeways.com/product/7T...li=marketplace

https://images1.sw-cdn.net/product/p...1459329887.jpg

Huumori 11-16-2017 09:13 PM
Re: Axle shaft dimensions for MRC
 
Yes i would if i had mrc axles but i have rc4wd's yota2 axles and those aluminun hubs and knuckles :/


All times are GMT -6. The time now is 04:19 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com