RCCrawler Forums

crazydevil97 · 01-31-2008, 09:39 PM

Ok so I have an EMAXX that I have taken parts off of and put onto a roc-maxx chassis (EVX speed control and reciaver) I have also put in an Integy 55T hand wound V10 crawler pro motor. I put it all together running 1 motor and 1 battery and it crawled beautifuly, problem is it was very late and i put it together backwards ( battery in back and electronics in front). The next day I took it apart and tried to remedy that but my wires are 2 short so I put it back and now it has no power whatsoever with a newly charged battery. Due to not being able to find a wiring diagram of the EVX I jus picked a pair of motor wires and connected the motor and it heated up to almost 200 degrees F. Did I fry my motor or ESC and Does anyone know where I can get a wiring diagram of the EVX?

dacaur · 01-31-2008, 09:51 PM

if it got that hot, its probably wrecked... please never post in blue again, it hurts my eyes to read.... I would look for a diagram, but i have a headache now....

crazydevil97 · 01-31-2008, 10:20 PM

ya sorry bout that I have a tendency to over do it with the blue sometimes. I have been searching for hours for a diagram for it and haven't gotten anywhere. I dont wanna fry another motor by guessing so any help would be greatly appreciated.

allgm1 · 02-01-2008, 04:27 AM

is this what yer lookin for http://www.rccrawler.com/evx.htm

crazydevil97 · 02-01-2008, 09:59 AM

Unfortunately not. I found that earlier and it did nothing for me, but i did finally find a diagram on traxxas' website. Thanks for all the input

mudboger07 · 02-04-2008, 06:38 PM

Is this a good esc for a clod using 2 45t motors? I hooked my xl1 up to 7 cells and i think it fried.....not sure why.....

01-31-2008, 09:39 PM	#1
crazydevil97 Newbie Join Date: Dec 2007 Location: Layton Posts: 31	EVX Integy 55T problems!!!!!!!!! Ok so I have an EMAXX that I have taken parts off of and put onto a roc-maxx chassis (EVX speed control and reciaver) I have also put in an Integy 55T hand wound V10 crawler pro motor. I put it all together running 1 motor and 1 battery and it crawled beautifuly, problem is it was very late and i put it together backwards ( battery in back and electronics in front). The next day I took it apart and tried to remedy that but my wires are 2 short so I put it back and now it has no power whatsoever with a newly charged battery. Due to not being able to find a wiring diagram of the EVX I jus picked a pair of motor wires and connected the motor and it heated up to almost 200 degrees F. Did I fry my motor or ESC and Does anyone know where I can get a wiring diagram of the EVX? Last edited by crazydevil97; 01-31-2008 at 10:20 PM.

01-31-2008, 09:51 PM	#2
dacaur Quarry Creeper Join Date: Jan 2008 Location: Eagle Mountain, Utah Posts: 311	if it got that hot, its probably wrecked... please never post in blue again, it hurts my eyes to read.... I would look for a diagram, but i have a headache now....

01-31-2008, 10:20 PM	#3
crazydevil97 Newbie Join Date: Dec 2007 Location: Layton Posts: 31	ya sorry bout that I have a tendency to over do it with the blue sometimes. I have been searching for hours for a diagram for it and haven't gotten anywhere. I dont wanna fry another motor by guessing so any help would be greatly appreciated.

02-01-2008, 04:27 AM	#4
allgm1 Quarry Creeper Join Date: Nov 2007 Location: NH Posts: 427	is this what yer lookin for http://www.rccrawler.com/evx.htm

02-01-2008, 09:59 AM	#5
crazydevil97 Newbie Join Date: Dec 2007 Location: Layton Posts: 31	Unfortunately not. I found that earlier and it did nothing for me, but i did finally find a diagram on traxxas' website. Thanks for all the input

02-04-2008, 06:38 PM	#6
mudboger07 Rock Crawler Join Date: Jan 2008 Location: Arlington, TN Posts: 624	Is this a good esc for a clod using 2 45t motors? I hooked my xl1 up to 7 cells and i think it fried.....not sure why.....

Sponsored Links

RCCrawler Forums

Thread: EVX Integy 55T problems!!!!!!!!!