03-28-2020, 03:02 PM | #1 |
Newbie Join Date: Aug 2019 Location: North Branch
Posts: 10
| 1080 esc help!
Hello everyone! I am having some serious problems calibrating my 1080 ESC. Let me add that I have watched a ton of videos and read other threads...I feel as though I have a very good understanding of the process and how it is supposed to work. Here is the rundown...when I turn on the ESC and enter calibrate mode, all is well. However, when I try that first calibration (neutral), it doesn't beep and just turns the LED off completely. I have steering, I have LEDs, I have no throttle. When I just turn it on normally as though I'm going to crawl, I get 3 beeps (running 3s battery), but no single follow-up beep to signal "ready". It instead blinks constantly with no end in sight. Here is a list of the troubleshooting steps I have tried: - Factory reset ESC - Factory reset ESC with programming card - Re-bound my Tx and Rx a dozen times - Quadruple checked that both my Trim and Fine trim are at 0 - Disconnected my servo, keeping only the ESC wired to the Rx - Swapped batteries - Checked motor wires and flip-flopped them - Tried the 3-prong wire from ESC to Rx in both directions Here is a list of the components I have: Transmitter - Spektrum DX5C Receiver - SR6100AT ESC - Hobbywing 1080 Motor - Holmes Hobbies CrawlMaster 16T Batteries - 3S 3500mAh Servo - Savox SA-1230SG Any help you can provide is greatly appreciated. I am 90% done with my first build and am dying to crawl! The sad part is, our local hobby shop is closed for 2 weeks due to COVID. |
Sponsored Links | |
03-28-2020, 03:32 PM | #2 |
RCC Addict Join Date: Jun 2016 Location: Germany
Posts: 1,364
| Re: 1080 esc help!
Try to calibrate with throttle set to reverse. The 1080 need this on some Radios
|
03-28-2020, 03:39 PM | #3 |
Newbie Join Date: Aug 2019 Location: North Branch
Posts: 10
| Re: 1080 esc help!
Thanks for the suggestion. Unfortunately that didn’t work :(
|
03-28-2020, 05:00 PM | #4 |
Pebble Pounder Join Date: Feb 2016 Location: Shelby
Posts: 163
| Re: 1080 esc help!
Try increasing the neutral range with the program card.
|
03-28-2020, 05:36 PM | #5 |
Newbie Join Date: Aug 2019 Location: North Branch
Posts: 10
| Re: 1080 esc help! |
03-28-2020, 05:43 PM | #6 |
Pebble Pounder Join Date: Feb 2016 Location: Shelby
Posts: 163
| Re: 1080 esc help!
That would be the way to fine tune it, think I jumped up like 2 steps from stock and it worked for me so I just left it.
|
03-28-2020, 05:46 PM | #7 |
Newbie Join Date: Aug 2019 Location: North Branch
Posts: 10
| Re: 1080 esc help! |
03-28-2020, 05:51 PM | #8 |
Pebble Pounder Join Date: Feb 2016 Location: Shelby
Posts: 163
| Re: 1080 esc help!
Have you tried reverse > neutral > forward? If that works you can reverse throttle after.
|
03-28-2020, 05:52 PM | #9 |
Newbie Join Date: Aug 2019 Location: North Branch
Posts: 10
| Re: 1080 esc help!
Sadly I have. I don’t know what’s,going on with this thing...I’m guessing it’s defective but thought I would ask around Sent from my iPad using Tapatalk |
Tags |
calibration, hobbywing 1080 |
1080 esc help! - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Is the 1080 the best BRUSHED esc ? | Frank211 | Electronics | 26 | 07-14-2022 09:02 PM |
1080 ESC on 4s | heavyD | Electronics | 6 | 06-15-2019 01:25 AM |
Hobbywing 1080 esc | Bjorn | Electronics | 2 | 03-18-2019 12:36 PM |
HW 1080 esc and 7.4v servo | garage-boo | Newbie General | 24 | 03-10-2019 04:21 PM |
| |