08-16-2007, 01:41 AM | #1 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
| motor prob
well i ended up getting a high lift. Now i just got a integy 55t motor. and it won't turn. i think it has something to do with my esc but im not certain becasue it say 16t and up. its the DuraTrax IntelliSpeed 16T Mild-Modified Reverse ESC. |
Sponsored Links | |
08-16-2007, 02:23 AM | #2 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
nevermind i figured it out.
|
08-17-2007, 01:26 AM | #3 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
ok still have a prob it only goes forward. Same Q about the esc.
|
08-17-2007, 02:58 PM | #4 |
I wanna be Dave Join Date: May 2005 Location: Anchorage, Alaska
Posts: 2,048
|
That ESC has a reverse lockout feature. Make sure that it is disabled. Also check the reverse delay setting.
|
08-18-2007, 03:01 AM | #5 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
yea i tried going through the set up over again. i did the reverse delay thing as low as it goes. Thanks for the help though
|
08-20-2007, 12:34 AM | #6 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
anybody else have any suggestions? i hooked up the original motor and it doesnt go in reverse now.
|
08-20-2007, 12:40 AM | #7 |
Rock Crawler Join Date: Jul 2007 Location: Portland,OR
Posts: 888
|
This sounds dumb but did ya pullthe antenna all the way out of the radio when ya tested it? Spent a half hour trippin' cuz minre wouldn't back up and realized (finally) the signal was weak. Sorry to sound patronizing, but only the best intentions I assure you! lol
|
08-20-2007, 12:51 AM | #8 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
i was gonna see if this was the prob next im almost possitive its not becasue it worked when i first got it together and all i changed was the motor but i am trying this in a few minutes.
|
08-20-2007, 09:24 PM | #9 |
Rock Crawler Join Date: Jul 2007 Location: Portland,OR
Posts: 888
|
Did ya figure it out yet?
|
08-20-2007, 11:26 PM | #10 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
nope. i think ive tried everything i can think of. im thinking i fried my esc. it lights up in reverse but doesnt send power.
|
08-21-2007, 01:00 AM | #11 |
Newbie Join Date: Jul 2007 Location: Port Angeles
Posts: 41
|
good luck with your problem again this might sound dumb but the same thing happened to me turns out i had a bare wire touching my metal chassis. or maybe your motor wires are backwards?? hope u figure it out |
08-21-2007, 02:42 AM | #12 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
switching the motor wires just makes it go backwards. no wires touching anything. its weird because the esc will light up when in reverse but doesnt send any power to the motor.
|
08-21-2007, 01:27 PM | #13 |
Rock Crawler Join Date: Jul 2007 Location: Portland,OR
Posts: 888
|
Sounds like it could be fried LOL
|
08-22-2007, 01:09 AM | #14 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
yea im gonna send it in so i hope it is. so i don't have to pay for the charges.
|
08-22-2007, 07:39 AM | #15 |
RCC Addict Join Date: Mar 2007 Location: MS Gulf Coast
Posts: 1,949
|
Toss it and get a new ESC! |
08-23-2007, 01:40 AM | #16 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
That'll cost more money. if they fix it for free then i don't have to spend money. Also i looked for one at my LHS and they didn't have any that i wanted.
|
08-25-2007, 01:11 AM | #17 |
Newbie Join Date: Feb 2006 Location: Minnesota
Posts: 31
|
I am sure you did this already, but check ALL connections that are visible. Make sure All motor connections and battery connections are good on the battery, esc, and motor. Also, dont forget the RX Plug, that can cause simple problems too.
|
08-25-2007, 02:42 AM | #18 |
Newbie Join Date: Aug 2007 Location: CO sprgs
Posts: 20
|
yea i checked everything tried different channels, recharged batteries. Cant try anything else now i sent it back.
|
| |