3d printing bodies I have been wanting to 3d print a body for a upcoming build but i am not sure what material would be best suited for the job. We frequently camp in the summer and the rc's tend to stay in the trailer between trips unless repairs are needed and im afraid if i leave a printed body it would get to warm and melt. Any recommendations? |
Re: 3d printing bodies ABS, PETG would be my best education guess. |
Re: 3d printing bodies Quote:
PLA isn't a terrible option for printing, but it can be brittle, and will be more-so with UV exposure. At the very least you will want to paint the body to protect it, and most likely use filler to sand out the print lines. PETG is a great option, it is a bit more durable than PLA, and a bit more UV resistant. But, to do the body justice, you will still want to fill, sand and paint. ABS works really well for bodies. Again, to get the print lines gone, fill, sand and paint. For most sub $2k printers, ABS is finicky to print with due to warping. Plus, you need good ventilation, ABS produces a good amount of fumage when printing. |
Re: 3d printing bodies Quote:
|
Re: 3d printing bodies PETG is probable the easiest, ABS the best .....dont forget that printed bodies are heavy as f..k ;) |
Re: 3d printing bodies Quote:
I was wondering if a vase-print body would work... Attachement points would needed to be beef up, and it would be crazy flexible. I am guessing it would not last more than a couple of packs with minimal abuse. |
Re: 3d printing bodies Quote:
Petg is really difficult to get a brand/type that isn't extremely brittle (almost no impact resistance) So far of 10 brands of petg I've found one that's not garbage for RC use. Explodes on impact. For pla, well more specifically, PLA+/PRO/Tough I have found multiple brands that can take a beating and come back for more. Petg with the right type and design, is good for when you need black if summer's get hot where you are. Pla dark colors tend to soften in the sun over about 90F. End up warping and such. Beyond that, PLA is a far better choice for RC than PETG could hope to be now. I have 4 rigs, 3 with printed bodies now. All in pla. First test was done in petg, ya that started falling apart due to cracks after second roll over. Decent tumble and spent 10 minutes picking up parts. Reprinted body in Tough PLA, I can't hurt it so I have an excuse to reprint it because it was printed fast and not dialed in for a clean print. Second rig is rather heavy, tumbled and slid several times when out, no body damage at all. Now my vanquish build will have a printed body as well. Also have printed cages, one I just did was a cliffhanger cage for someone. Can twist and bend it all you want, good luck breaking it. Printed in PLA.https://uploads.tapatalk-cdn.com/202...4d716091ee.jpghttps://uploads.tapatalk-cdn.com/202...b05bf61581.jpghttps://uploads.tapatalk-cdn.com/202...616768eab1.jpg Sent from my SM-S906U using Tapatalk |
Re: 3d printing bodies tigris99 covered it all there. I've had no heat or durability issues with PLA printed bodies either. Post print work completely sucks for me though, I hate sanding. |
Re: 3d printing bodies thanks for all the great info guys i guess i will try starting with a pla body and see how things go i just didnt want to go through all the time and labor of printing and all the body work jsut to have it soften and warp right away |
Re: 3d printing bodies Quote:
|
Re: 3d printing bodies Quote:
Sent from my SM-S906U using Tapatalk |
All times are GMT -6. The time now is 08:32 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com