Rolandrockshop's TF2 Build ..FINALLY!! Finally got a TF2!! Thanks to JASON!"thumbsup" http://i122.photobucket.com/albums/o...IMAG2526-2.jpg Been wanting one since they cameout.. Gonna keep it 1.55 based. plans so far.. bob the bed steel sliders,bumpers interior roll bar lights anti wrap bar specs for electrics.. HH brxl wp HH30t CC BEC Hitec 5955tg servo 3s 2200mah lipo hitec 645mg servo for shifting axle upgrades.. helical gears Hd cvds/xvds .... |
Re: Rolandrockshop's TF2 Build ..FINALLY!! start by tearing down the transfer case and trans... greasing them up proper.. http://i122.photobucket.com/albums/o...IMAG2527-1.jpg http://i122.photobucket.com/albums/o...IMAG2528-1.jpg http://i122.photobucket.com/albums/o...IMAG2529-1.jpg http://i122.photobucket.com/albums/o...IMAG2531-1.jpg as you can see they were "lightly" greased from factory.. greased and reassembled.. onto framework!! . . http://i122.photobucket.com/albums/o...d/IMAG2532.jpg http://i122.photobucket.com/albums/o...d/IMAG2533.jpg http://i122.photobucket.com/albums/o...d/IMAG2536.jpg Dad's ol'yota build body ive been itching to use again.. now it fits proper! http://i122.photobucket.com/albums/o...d/IMAG2535.jpg 1st scale event/comp..LRC,Alabama..1st in 2.2 and 3rd in 1.9..both on xtrail chassis. Got me hooked on scalin!! |
Re: Rolandrockshop's TF2 Build ..FINALLY!! moved the shock hoops back.. and the shocks to backside of axles.. *stock location* http://i122.photobucket.com/albums/o...d/IMAG2538.jpg relocated.. http://i122.photobucket.com/albums/o...d/IMAG2539.jpg http://i122.photobucket.com/albums/o...d/IMAG2540.jpg swapped frame mounts..shackles to the rear on front leafs.. an oring and washer to keep things quiet.. http://i122.photobucket.com/albums/o...d/IMAG2541.jpg http://i122.photobucket.com/albums/o...d/IMAG2542.jpg and over the leaf steering is now accepted. .. |
Re: Rolandrockshop's TF2 Build ..FINALLY!! <iframe width="640" height="360" src="//www.youtube.com/embed/2g_DFdc4M8M" frameborder="0" allowfullscreen></iframe> |
Re: Rolandrockshop's TF2 Build ..FINALLY!! updated.. |
Re: Rolandrockshop's TF2 Build ..FINALLY!! The screws holding the leafs... take the screws thread them from the bottom and use locknuts on top. Tighten the nuts down and back them off 1/4 turn or so. It will help with the flex. |
Re: Rolandrockshop's TF2 Build ..FINALLY!! Looking good... |
Re: Rolandrockshop's TF2 Build ..FINALLY!! Quote:
"thumbsup" Quote:
now if Rc4wd would just get restocked on what I need for the axles..;-) |
Re: Rolandrockshop's TF2 Build ..FINALLY!! I been told to skip the red leafs. Try building your own leafs. Start collecting different sets and build one that works for your truck. Ultimately.. if you can track down chino63 military wrap springs those would be the best setup. Love the color and wheel & tire combo! Just needs scale hardware everywhere. |
Re: Rolandrockshop's TF2 Build ..FINALLY!! Quote:
|
That makes 3 of us^^^^ Sent from my SCH-I545 using Tapatalk |
Re: Rolandrockshop's TF2 Build ..FINALLY!! yep..gears and xvds.. |
Re: Rolandrockshop's TF2 Build ..FINALLY!! I couldn't wait to get it rolling... so I used what electrics I had on hand till I get the elec on spec list. cc micro sidewinder / cc bec 6.3v Hpi X re 30t motor OmG 275oz servo for steering / 645mg shifter servo http://i122.photobucket.com/albums/o...d/IMAG2544.jpg http://i122.photobucket.com/albums/o...d/IMAG2546.jpg http://i122.photobucket.com/albums/o...d/IMAG2543.jpg |
Re: Rolandrockshop's TF2 Build ..FINALLY!! Outside in my Rc Orv test grounds.. http://i122.photobucket.com/albums/o...d/IMAG2552.jpg http://i122.photobucket.com/albums/o...d/IMAG2550.jpg http://i122.photobucket.com/albums/o...d/IMAG2547.jpg http://i122.photobucket.com/albums/o...d/IMAG2554.jpg http://i122.photobucket.com/albums/o...d/IMAG2555.jpg http://i122.photobucket.com/albums/o...d/IMAG2558.jpg http://i122.photobucket.com/albums/o...d/IMAG2559.jpg http://i122.photobucket.com/albums/o...d/IMAG2560.jpg http://i122.photobucket.com/albums/o...d/IMAG2561.jpg http://i122.photobucket.com/albums/o...d/IMAG2564.jpg Love it so far!! "thumbsup" |
Re: Rolandrockshop's TF2 Build ..FINALLY!! Took the TF2 out today to flex the springs... checking out a new crawl spot. http://i122.photobucket.com/albums/o...d/IMAG2578.jpg http://i122.photobucket.com/albums/o...d/IMAG2577.jpg http://i122.photobucket.com/albums/o...d/IMAG2579.jpg http://i122.photobucket.com/albums/o...d/IMAG2586.jpg http://i122.photobucket.com/albums/o...d/IMAG2587.jpg http://i122.photobucket.com/albums/o...d/IMAG2588.jpg the leafs take some getting used to.. the 2spd is just too nice,esc,motor never got warm or hot..cool.8) the 1.55 stompers aren't bad.. but.. I cant wait to get those 1.55 growlers on here. Just got to decide on beadlock..?? |
Re: Rolandrockshop's TF2 Build ..FINALLY!! the new spot.. http://i122.photobucket.com/albums/o...0/IMAG2583.jpg http://i122.photobucket.com/albums/o...0/IMAG2581.jpg http://i122.photobucket.com/albums/o...0/IMAG2571.jpg spent 3hrs and didn't cover half of it.. so many waterways and channels just right for crawlers. |
Re: Rolandrockshop's TF2 Build ..FINALLY!! Great looking spot, I wish I had some of that moss rock for my ongoing landscape project. |
Re: Rolandrockshop's TF2 Build ..FINALLY!! Quote:
http://img.photobucket.com/albums/v1...ps206b89c6.jpg |
Re: Rolandrockshop's TF2 Build ..FINALLY!! I was thinking more like these... slw compatible.. http://www.rccrawler.com/forum/vendo...55-wheels.html http://motoworxracing.com/wp-content...Hole_LE_07.jpg |
Re: Rolandrockshop's TF2 Build ..FINALLY!! Got a DinkyRc yota interior coming for the TF2.. http://www.rccrawler.com/forum/dinky...interiors.html Gonna use the body I have now as a trail beater body. And fix up the Mojave body that came with for more scale details. "thumbsup" |
All times are GMT -6. The time now is 10:35 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com