Antenna tube. I can't seem to feed the cable through the tube. Is there a trick to doing so. Also I was thinking about upgrading my servos with a couple of these. http://cgi.ebay.ca/ws/eBayISAPI.dll?...=STRK:MEWAX:IT Do I need to add a bec or will it run ok like it is. I'm not in any compition. One last question please. I seen this on redcat's website. http://www.zno-rc.com/pages/products...te_stage1.html Is this so I can use a flat pack. Thanks. Gates |
Sprinkle some baby powder or talcum powder on the antenna wire to make it slippery and it will slide right through the tube. Narly1 |
Baby powder worked great. Thanks."thumbsup" |
I have no experience with those servos, but based on their torque ratings they should be better than stock. As far as them working without a BEC is concerned...they may or may not. When I upgraded to my new servo my rig glitched like crazy until I put a BEC in. The BEC supplies more power to your servos resulting in more torque...they're never a bad thing, whether you comp or just drive around for fun. |
I would like to add a bec but too bad they don't make one that is plug and play. I don't like the fact of cutting wires. Too bad they don't make them like before. They ran on extra 4 AA batteries. |
I should be getting some servos almost like those, I think the only difference is the sticker on the front, I also recieved a bec yesterday in preperation of the new servos. I will let you know how they do, hopefully this afternoon !"thumbsup" |
It would be nice if you could let me know if they work without the bec. Also a picture of your bec installed. Thank you so much. |
Quote:
|
I'm not great at soldering. I always wanted to buy some new tools to solder but don't know where to start. I have two soldering irons but none of them seem to work good. One small pin type and a large gun type. There are some with an open flame but don't know how well those work. It might be the solder I'm using? |
I'm pretty sure these replace or update the MG995 servos - which initially got horrible reviews. I've seen pretty good reviews for the MG996's but it may be worth the time to google these and check out the reviews. Based on what I've read, for a crawler application they will probably work well but I would not want to use them in a plane...;-) Regards |
Everytime I play around a little with this thing I find more problems. Now the transmitter antenna is falling apart. One of the section is very loose and I see a copper ring that shows up. Only on the second battery charge. I doubt that redcat will replace this. I sent a request for new servos early this morning. No reply yet. I'll try to send another for this now. Not expecting a reply anytime soon. They might not warranty anything since I live in Canada.:cry: |
Quote:
|
It may cost you a couple extra bucks for shipping but you should not have any problems with getting fixed up. |
They only have a 30 day warranty on electronics not lifetime. If I have to pay to ship something back to them it would be cheaper for me to buy it here. I sent the 2 e-mails yesterday. One first thing in the morning and nothing. Well see what happens but I will be selling this thing. Too cheaply made for me. |
http://www.redcatracing.com/information/warranty.html 90 day limited waranty Lifetime electronics replacement program. After the 90 days they only charge you a portion of the cost of a given item, even if you smash it with a hammer (It will just cost a little more for misuse.) |
Still have to send old parts back. Shipping from Canada to us is very high. Might as well buy new on ebay. Cheaper. That is how they get you. No one will bother to send in a claim. Atleast that is how I think it is. They still have not replied to me yet. |
Quote:
|
I wonder if redcat will send me a replacement. I don't have a dealer near by. Atleast I know now that they are easy to find. I thought this might be something that only one type of antenna fits. Thanks to all for your reply's. |
I had the same problem with my antenna so i got some fishing line and fed it down the tube then tied it to the antenna cable and pulled it back through the tube worked great. |
http://cgi.ebay.com/2x-MG996R-Metal-...item41539bfd8c These are the servos that I installed today along with a UBEC that I got for $10.00 shipped. The UBEC has an output of 6v at 3A, which is probably the most your gonna get out of your stock battery. I saw significant improvment over stock ! I ran the servos without the bec at first just to see if I could tell a difference in the servos from stock and I really didn't see that much change, hooked up the bec and they came to life !! So in conclusion, a bec is a must ! And I recomend these servos for the price!"thumbsup" |
All times are GMT -6. The time now is 10:57 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com