Re: Soze adds a RedCat to the fleet - Gen8 Scout II Here's the first thing that I wanted to adjust. The steering geometry is off out of the box, and it kind of bothered me. Look how far out in front the servo end of the draglink is. I haven't gotten around this part yet, but sooner or later I hope it can be addressed https://farm8.staticflickr.com/7837/...e9e4680c_b.jpg Here you can see that the draglink and panhard rod are not at the same angle. The panhard rod has a steeper angle than the draglink. https://farm8.staticflickr.com/7901/...90f4e62f_b.jpg Part of the reason for a shallower draglink angle is due to the stock servo horn that comes with the truck https://farm8.staticflickr.com/7921/...e9b00988_b.jpg Since I didn't have anything suitable on hand, I wanted to see if there was something I could do while I waited for the parts I needed. I ended up figuring out how to get the correct angle just by moving the tie-rod below the knuckle mounting point rather than above. This allowed me to get the correct angle while using the stock servo horn. Don't have pictures, but here's the video: https://youtu.be/q2BiP4YPJfs While I was at it, I took the opportunity to swap receivers. I thought the RedCat receiver would work with my FlySky GT3C since it's FlySky based, but apparently not. They must've done something to the Redcat version to make it RedCat specific. See the similarities between the RedCat and the Fly Sky Receivers? https://farm8.staticflickr.com/7909/...ae45f4f2_b.jpg Also took a look at my portal gears to see if they were missing grease. Lots of the earlier batches were reporting dry portal gears. Luckily my February release was all greased and ready to go. https://farm8.staticflickr.com/7909/...03962cf3_b.jpg https://farm8.staticflickr.com/7838/...e782d64f_b.jpg https://farm8.staticflickr.com/7865/...ef69981f_b.jpg |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II The RedCat body mounting system is a good idea, but the execution with the velcro left a little to be desired. Here are some issues that I had. Dropping the body straight on never worked well. The front just wouldn't stick. https://farm8.staticflickr.com/7888/...12616aae_b.jpg This is the type of misalignment you get when you drop it straight on from the top https://farm8.staticflickr.com/7838/...00c2042d_b.jpg The secret to getting it mounted on correctly was to mount the front first, and then drop the back on. https://farm8.staticflickr.com/7894/...78e10bbf_b.jpg https://farm8.staticflickr.com/7844/...45901362_b.jpg Another issue is the side trim on the body prevents the body from mounting all the way down. It hits up against the sliders preventing the body from going down a bit more snugly. https://farm8.staticflickr.com/7890/...21c84539_b.jpg https://farm8.staticflickr.com/7903/...6250c4ff_b.jpg This is something I'll address by trimming the sides, but I'm reluctant to do it until I get my magnets in. I'll be swapping out to magnets. It's the way to go. <iframe width="560" height="315" src="https://www.youtube.com/embed/Z3rpMcMVnAo" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Despite those issues that I posted about above, I had a chance to take it out for a run, and it did pretty well. I hate the way the stock tires look, and the foams were garbage. So I stuck the Pro-Line Hyrax with Pro-Line Dual Stage Foams on ebay beadlocks that I was using for my MST CFX-W. https://farm8.staticflickr.com/7849/...17990e19_b.jpg https://farm8.staticflickr.com/7891/...ba41bdfe_b.jpg https://farm8.staticflickr.com/7840/...91e028f9_b.jpg https://farm8.staticflickr.com/7818/...761395ff_b.jpg https://farm8.staticflickr.com/7902/...4dafee51_b.jpg https://farm8.staticflickr.com/7885/...34830598_b.jpg https://farm8.staticflickr.com/7906/...feb992de_b.jpg <iframe width="560" height="315" src="https://www.youtube.com/embed/i9swM6Kk6Aw" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Another annoying thing. The driveshafts are out of phase, and there's nothing I can do about it on the stock shafts. The steering geometry and these driveshafts make me wonder if it's just unfamiliar territory, or lack of attention to detail. https://farm8.staticflickr.com/7839/...a3309850_b.jpg https://farm8.staticflickr.com/7841/...4026091d_b.jpg I was looking into the RedCat upgraded driveshafts, but HumboldtEF mentioned that they were still out of phase. I'll probably to see what cheap generic driveshafts might work on this truck. I tried the Axial WB8 Driveshafts, and the length is good. The only issue with those is the different screw size diameter for holding the driveshaft in place. The Axial ones are a bigger diameter. |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Take two on the steering mod. I decided to move the draglink from connecting at the tie-rod to connecting at the top of the knuckle like some others here have done. The ProTek RC low-profile servo horn finally came in and I was all ready to go until I got this... I couldn't get the angle I wanted, because the rod-ends didn't allow for it. https://farm8.staticflickr.com/7857/...41528d68_b.jpg So I used SSD RC M3 bent rod-ends. They're roughly the same length in order to keep the draglink the same length as the panhard rod. https://farm8.staticflickr.com/7866/...21b86aee_b.jpg Now I'm a happy camper for as far as I can go without a new bumper/servo mount design. Side to side suspension bump steer improved with this change. https://farm8.staticflickr.com/7889/...e4a2243d_b.jpg https://farm8.staticflickr.com/7825/...9e4309dd_b.jpg |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Cool write-up! However, the last post is a double of the one prior to it... "thumbsup" Otherwise, extremely well-documented and informative. |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II As always. Just posted this thread on my Facebook face and tag a buddy who recently bought a blue car. I urge him must read through this thread. "thumbsup" |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Great write up about these, I'm not happy about the front suspension geometry either, I'll get around to doing something with it at some point for sure though. |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II I did away with the stock rock sliders all together, they seemed to get hung up more than the skid plate.https://uploads.tapatalk-cdn.com/201...15c7a4fd89.jpghttps://uploads.tapatalk-cdn.com/201...d6957e5d58.jpghttps://uploads.tapatalk-cdn.com/201...b4bf44578b.jpghttps://uploads.tapatalk-cdn.com/201...eb84b72b6f.jpg Sent from my SM-G920R6 using Tapatalk |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Roadrashracing, what sliders did you replace them with? |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Interesting on the redcat rx, i used a redcat rx on my monster beetle and my flysky gt3c with no issues... |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Quote:
Quote:
Quote:
|
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Quote:
|
Soze adds a RedCat to the fleet - Gen8 Scout II Hey Soze I recently did a custom build with wild boar shafts paired with Gmade axles. I had the same issue with the shaft pin being too big. Luckily I had a pair of Gmade shafts lying around, so I took the screw pin and they fit the wild boar threads and pin fit on the pinion. Hope that helps. Sent from my iPhone using Tapatalk |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Quote:
|
Re: Soze adds a RedCat to the fleet - Gen8 Scout II I have found rc4wd bumpers with the outside tabs fit.https://uploads.tapatalk-cdn.com/201...6fff23aa92.jpghttps://uploads.tapatalk-cdn.com/201...4f267a847c.jpg Sent from my SM-G920R6 using Tapatalk |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II That bumper is an excellent choice. You guys are really making these Gen-8s look G-R-R-R-E-A-T! Now about the shape of those fenders... (j/k) |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II Nice work. I watching how these builds go. Might be a while, but I do like these Gen 8's. I can't 'like' posts atm. Anyone else got this happening? |
Re: Soze adds a RedCat to the fleet - Gen8 Scout II If you let me know when you're hitting El Modina we'll come join you. ;-) One of my crawling buddies just got one of these, I sent your thread link. |
All times are GMT -6. The time now is 01:31 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com