Official G6/KOH/Rock Race Rules & Rigs Thread
 

i wanted to post up a G6/KOH/Rock Race thread so people can read the rules and post pics and specs on their scale rigs. hopefully some of the NC and GA scale guys will chime in and possibly attend a few events or host some at thier crawl spots as well. "thumbsup"



RULES

course/rig rules: (these are NOT set in stone, just a base for the first few events until we can see what needs to change to make it bettrer)

1. 1.55/1.9 and 2.2/wraith classes (no moa)
2. must be a scale chassis (no twin vertical plate)
3. 5 minimum scale accessories (winch/tow strap reccomended)
4. scale type tires both classes (no comp tires sedonas/rovers/ect.)
5. "X" number of sections using survey tape as boundaries. each section will be marked by a numbered tennis ball gate at the entrance.
6. sections must be ran in numerical order
7. sections will be no less than 12" wide at any point
8. orange ribbon will always be on the right to note direction
9. no "hand of God" roll overs or repositions
10. no driver will straddle a boundry to get progression
11. no dig/rear steer (may change once we see these being installed more)

judges

1.judges calls are final.
2. judges will have a tow strap known as a "judges winch". theses can be used for rollovers or to help you get progression but use comes with a penalty.

skills section/bonus sections

1. skills section are mandatory
2. bonus sections are optional. time bonuses will be determined on the obsticle.

*skills section can be any task i driver is asked to perform during thier run on the course. (changing a tire, pulling an object a certain distance, ect.)
*bonus sections will be variuos obstacles. (hard climbs, rope bridge, jumps, ect.)


penalties/progression

1. section progression- 2 minutes off time total
2. boundry marker- 1 minute per tire that touches or exits boundry up to 4 minutes(if all 4 tires exit boundry the driver must re-enter the section at entrance)
3. winches- no penalty for winch mounted on rig/judges winch- 3 minute penalty
4. straddling boundry- no progression and 10 minute penalty
5. non-completion of skills section- 30 minute penalty
6. non-completion of set sections- total time on course plus 1 hour


**NOTES**

1. i added the no dig/rear steer rule. this may change if interest in it grows. anyone with these installed MUST lock them into position before running the course. use of dig or rear steer on the course will result in a DNF with the max time penalty. if we do any heads up runs on the course after the comps it will be allowed.


2. scale chassis examples- SCX10, TCS X-trail/L-trail, Scale shop, Tamiya hilift, Timberwolf, any life like tube chassis, ect.


3.scale accessories(must be an additional item found on a 1:1 rig)- winch, tow strap, hilift jack, spare tire, shovels, axes, coolers, sleeping bag, license plate, ect...



RIG SPECS

body:
chassis:
axles:
trans:
motor/esc:
servo:
tires:
wheelbase:
favorite bolt on mod:
favorite mod you designed/made:
upcoming mods:



hope to see all of you at an event soon. i am working on getting us an event going and all help, input, and suggestions are appreciated.

i will start it off

My Hilux:

http://i108.photobucket.com/albums/n...z/IMAG0495.jpg

RIG SPECS

body: dove nosed hilux/honcho bed
chassis: SCX10
axles: Axial
trans: Axial
motor/esc: Tekin FXR/ Tekin 35t
servo: 7955tg
tires: RC4WD 1.9 boggers
wheelbase: 12.3"
favorite bolt on mod: axial hi steer knuckles
favorite mod you designed/made: 5/16 delrin links w/ revo ends
upcoming mods: dovetailed bed

RCCrawler1396's (Jeremy) TJ

http://i108.photobucket.com/albums/n...z/IMAG0497.jpg

RIG SPECS

body: caged New Bright TJ
chassis: SCX10
axles: Axial
trans: Axial
motor/esc: Tekin FXR/ 45t
servo: 7955tg
tires: RC4WD 1.9 boggers
wheelbase:
favorite bolt on mod:
favorite mod you designed/made: 5/16 delrin links w/ revo ends
upcoming mods:

My C10 Flatbed

http://i1178.photobucket.com/albums/...w/IMAG0459.jpg

body: Proline C10
chassis: Scale shop
axles: Axial
trans: Axial W/ Robinson internals
motor/esc: Waterproof BRXL / Integey 35t
servo: Hitec 645
tires: RC4WD 1.9 boggers / Proline 2.2 Flatirons
wheelbase: 11.5"
favorite bolt on mod: 3 Racing winch
favorite mod you designed/made: Real wood bed / custom front bumper
upcoming mods: Better motor if I ever kill this Integey...its about 3 years old


Slowsis's DMG Nemesis

http://i1178.photobucket.com/albums/...w/IMAG0585.jpg

body: DMG Nemesis
chassis: DMG Nemesis
axles: Axial
trans: Axial W/ Robinson internals
motor/esc: Novak Rooster / Integey 55t
servo: Hitec 645
tires: Pitbull 2.2 Rock Beast
wheelbase: 12.5"
favorite bolt on mod: Scale window nets
favorite mod you designed/made:
upcoming mods: Waterproofing / New Panels

http://i1187.photobucket.com/albums/...Y/GEDC0413.jpg


RIG SPECS

body: Doved F/R Toyota Hilux
chassis: SCX10
axles: Wraith AR60
trans: Summit
motor/esc: MMP w/13.5 redline
servo: 7950 hitec
tires: Axial Ripsaws
wheelbase: 13"
favorite bolt on mod: Wraith axles
favorite mod you designed/made: XR10 skid/tranny mount
upcoming mods: Switching all steel tube work to aluminum

My Short Bus Wraith
UNDER HEAVY CONSTRUCTION
http://img.photobucket.com/albums/v2...s/IMAG0215.jpg
body: .020 Aluminum, stock hood
chassis: Wraith with some mods
axles: Wraith Ar 60?
trans: Stock
motor/esc: Anything... Holmes BRXL waterproofed
servo: Steering Hitec 7950, Winch Hitec 5645MG
tires: 2.2 TLS Super Swamper
wheelbase: 13 3/4
favorite bolt on mod: Banjo or Barrel of Woop A$$
favorite mod you designed/made: I guess the 3/8 tapered lower delrin links.
upcoming mods: Mg200 servo winch bumper, vp goodies.

My Wraith

<Currently In Build Process>

http://i843.photobucket.com/albums/z...xialblocks.jpg



body: Dinky RC hood and roof (being painted)
chassis: stock
axles: stock
trans: stock
motor/esc: Holmes 32T Crawlmaster Handwound, stock ESC
servo: HiTec 7954SH
tires: 2.2 HB Sedonas
wheelbase: stock
favorite bolt on mod: motor
favorite mod you designed/made: new interior (almost finished)
upcoming mods: Tekin FXR, punisher shafts, 2.2 Swampers on Vanquish SSZ-9's, Winch, Vanquish upper and lower links

RIG SPECS

body: Wraith
chassis: Wraith
axles: RC4WD XVD's Front /Axial Rear
trans: Axial w/ steel internals and 32p spur/pinion
motor/esc: HH 21t TQmaster/Waterproofed BRXL
servo: 7955tg (front & Rear)
tires: 2.2 RockGrabber on DNA Snipers
wheelbase: 14" Track:11.75"
favorite bolt on mod: VP titanium links & Rear Steer
favorite mod you designed/made: Carbon Fiber panels and hood inserts
upcoming mods: Winch

Started tearing the Jeep apart tonight and doing a complete rebuild on the shocks and axles. Then add more lighting and better electronics. Will add more updated pics as they come

http://i402.photobucket.com/albums/p...c/ScalerYJ.jpg

VERY nice YJ Eric!

Chassis: custom mg200 with full Exo cage with servo winch mount

Axles: axial with super 300s. Wraith's coming soon

Motor esc: tekin rx8 with 1400 kv t8 motor

Transmission: axial with all Robinson racing gears and 32p spur gear

Wheels tires: 2.2 Baja claws wrapped around vp ssz wheels

RIG SPECS

body:GCR Ambush, top off of discontinued GCR, Front and Rear LED’s
chassis: SCX10
axles: AX10 with HD gears
trans: Vp – Robinson Racing metal gears
motor/esc: Putnam 19T / HH BRXL
servo: Hitec 645
tires: 1.9 RC4WD Boggers
wheelbase: 11 ¾”
favorite bolt on mod: Vp Tranny
favorite mod you designed/made:
upcoming mods: Metal winch bumper



http://i1226.photobucket.com/albums/...1318351650.jpg

Somebody needs some wheel bearings and/or beef tubes and/or kingpin bushings! /----\

I was going for the baja look !!!!!

That was the old axles with wheel wideners that I didn't like but I'm selling the new axles I just got and never ran to get. Something a little wider thanks for all the tips

http://i1002.photobucket.com/albums/...INKING/003.jpg

http://i1002.photobucket.com/albums/...INKING/002.jpg

Still a loooong way to go yet. Longer beef toobs not installed in pics

RIG SPECS

body: Axial Trail Ranger
chassis: SCX10 and solid rod
axles: AXR-10, Felsenfast spools, OD/f, UD/r, VP knucks, STRC chubs f/r
trans: AX w/ HR hardened gears, steel outputs, 32p spur/pinion
motor/esc: Sidewinder w/ HH 10t puller on 3s
servo: HS-7950TG f, HS-5645MG r (probably gonna change)
tires: MT Baja Claw 2.2s
wheelbase: 14"
favorite bolt on mod: Longer Beef Toobs
favorite mod you designed/made: interior/rear bed area (yet to come)
upcoming mods: Tekin power!!!

Axles and Shocks torn down, relubbed and reassembled. SLWs with the 1.9 Rok Lox mounted. I trimmed every other lug on the outer edges to see if they'll work like the TSLs

http://i402.photobucket.com/albums/p...1101-00175.jpg

http://i402.photobucket.com/albums/p...1101-00178.jpg

http://i402.photobucket.com/albums/p...1101-00177.jpg

http://i402.photobucket.com/albums/p...1101-00176.jpg

Now it's time for a few more lights and maybe a roof rack with a couple accessories in it

the little YJ is looking bada$$ eric. "thumbsup" makes me want to keep my yota. :roll:

Agreed! "thumbsup"

X 3!!

x100 The YJ is a sleeper...:evil:

I've been thinking about big block style power for it but have to do some axle upgrades to handle the power. Sounds like I need to start making a list dont it