|
| LinkBack | Thread Tools | Display Modes |
04-05-2012, 11:13 AM | #1 |
Newbie Join Date: Apr 2012 Location: costa rica
Posts: 6
| ticava's madtorque proyect
hey guys! my name is luis im from costa rica and i just got a mad torque 1/8th scale. last 4 hours i have been working on it and here are some pics of my progress with it. any recomendation/opinion is welcome!!! body pics: *************************** mods! cable management steering upgrade, no more stress on the steering components lowered the servo mounting posts motor heatsink foams not in a star pattern just lowered from almost 2 inches to 1 remote: packed the gears and shafts with grease |
Sponsored Links | |
04-08-2012, 04:55 PM | #2 |
I joined the Band! Join Date: Feb 2012 Location: bay area
Posts: 66
| Re: ticava's madtorque proyect
Is the "steering upgrade" a temporary fix? I would think stock steering would be a lot better. The screws sticking out of the servo horn are going to snap the servo horn and ruin the approach angle. If you want good ideas look here: Super Experiment... :& and here: e's ExMT and here: Exceed Mad Torque From Box to Rocks........ Then buy a aluminum servo horn from Robitronic and you should be good to go Last edited by 707offroad; 04-08-2012 at 04:57 PM. |
04-08-2012, 04:59 PM | #3 |
Newbie Join Date: Apr 2012 Location: costa rica
Posts: 6
| Re: ticava's madtorque proyect
the steering upgrade is acyually permanent, materials will be changed of course but the idea is working fine, now the horn assembly is set kinda loose so when pressure is applied it wont bend the horn , somewhat like a servo saver, the twist at the knuckles is not there anymore so it is working, i will be changing the links to more mmm delicate fabrication methods , that was a test but is working preety well so far
|
04-18-2012, 06:15 PM | #4 |
Newbie Join Date: Apr 2012 Location: costa rica
Posts: 6
| Re: ticava's madtorque proyect
k got tired of going slow so im doing somewhat like a conversion mod fab , it will be a completely new car when im done... thinking of getting 20tpinion on the back and 19 on the front i have made some progress, and some pics as well check them out 6 point tire chains, rear completed and sealed the tires for waterproofing purposes got some materials to start my conversion... yeap cutting board for some DIY 4 link and lower links maybe something else cleaned up the steering mod im no good drawing but heres my attempt |
04-18-2012, 11:17 PM | #5 |
Newbie Join Date: Apr 2012 Location: costa rica
Posts: 6
| Re: ticava's madtorque proyect
beta phase on, here are some pics, so far so good before after |
04-18-2012, 11:53 PM | #6 |
I joined the Band! Join Date: Feb 2012 Location: bay area
Posts: 66
| Re: ticava's madtorque proyect
Too bad they don't make scale Thornbird tires they would be perfect for this thing
|
04-19-2012, 06:38 PM | #7 |
Pebble Pounder Join Date: Aug 2011 Location: Geneva, MN
Posts: 175
|
What's the ground clearance on that man.
|
04-20-2012, 08:56 AM | #8 |
RCC Addict Join Date: Apr 2010 Location: Ringwood
Posts: 1,233
| Re: ticava's madtorque proyect |
ticava's madtorque proyect - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
exceed rc maxstone & madtorque crawler pics here | creepr69 | General Crawlers | 39 | 11-03-2013 11:40 PM |
MadTorque hubs | Koldham | Superclass Crawlers | 1 | 11-30-2011 06:30 PM |
New Proyect The JeepStick!, aka EL PALO! | JeeperoManiako | General Crawlers | 20 | 12-16-2006 12:12 PM |
| |