Vedo's TRX4 Here is my TRX4 Build Log. Parts List: --Spektrum Dx5c with SRS6000 receiver --Hot Racing Battery Relocation Kit ( TRXF100FM01 ) --GPM Racing Aluminum Motor Heat Sink Motor Plate ( TRX4018 ) --Holmes Hobbies Puller Pro BL 540 2200kv --Holmes Hobbies Trailmaster BLE Pro WP --Holmes Hobbies HV500V2 Servo --Castle Creations BEC 2.0 WP --Incision TRX-4 Stainless Steel 10PC Link Kit - 12.3IN Wheelbase ( IRC00201 ) --SSD 25T Aluminum Servo Horn for TRX-4 ( SSD00224 ) --SSD D110 Aluminum Rear Bumper for TRX4 ( SSD00205 ) - not in use --SSD D110 Aluminum Front Bumper for TRX4 / SCX10 II ( SSD00203 )- not in use --Proline 1991 Toyota 4Runner body ( 3481-00 ) --Axial SCX10 Roll Cage Flat Bed ( AX80046 ) --Samix TRX-4 brass knuckle & hub carrier & portal knuckle cover & scale brake rotor & caliper set ( TRX4-4412C4 ) --Samix TRX-4 brass portal knuckle cover & scale brake rotor & caliper combo set ( TRX4-4413C2 ) --Samix TRX4 brass shock spring under cap (4pcs) (TRX4-4047) --Proline Hyrax 1.9 Tires ( 10128-14 ) --Gmade NR-01 beadlock wheels ( GM70225 ) https://i.imgur.com/9Fnt7CQ.jpg Here She is on Day 1. Bone Stock out of the box. https://i.imgur.com/9e495eq.jpg |
Re: Vedo's TRX4 First Mod I did was the SSD bumpers front and rear and spare tire delete. I Flipped the rear bumper for even more angle. https://i.imgur.com/CsoKPR4.jpg |
Re: Vedo's TRX4 Next up I Swapped out the stock steering servo for a Savox 0231MG I yanked out of my Yeti until my Holmes order came in. Threw in a Castle BEC and wired up the Deans connector. I mounted the inner fenders to the chassis as well using body screws. I chose to screw it to the frame instead of the zip tie method. I cut out the screw mounts for the fender flares but should have just cut off the whole section. DUH.:oops: Also I should add that my Traxxas receiver went in the garbage after one day. It refused to stay bound to the radio so I put a Spektrum 4ch in until I could decide between a DX8 stick radio or a Dx5c. I chose the Dx5c because I MAY want AVC for my other rigs at some point. https://i.imgur.com/xPJoq5B.jpg |
Re: Vedo's TRX4 Oh HELL yeah!! Holmes Order came in.. But. Something. Is. Missing. They forgot to ship my Hv500v2 servo =( Holmes Hobbies customer support is top notch. On a friday night, within 50 mins I had a tracking number in my email for the forgotten servo!"thumbsup" https://i.imgur.com/YQ1dsb3.jpg With the Holmes goodies dropped in, I decided while I was at it I'd swap out the transmission servo with the stock steering servo. Took a little more effort than it looks but it works great and gives you a spare diff locker servo. https://i.imgur.com/brZoKlM.jpg |
Re: Vedo's TRX4 Quick clip of trailing with the TRX4 with some Proline Sand Paws on Axial beadlocks. https://youtu.be/pcTd0HSDB2s |
Re: Vedo's TRX4 I was looking for something a little different body-wise for my TRX4 and decided to go with a Proline 4runner.....with a twist. https://i.imgur.com/B6UJ4Zf.jpg Axial Honcho cage https://i.imgur.com/mGnMA2z.jpg Knight Customs grille :mrgreen: https://i.imgur.com/4j8VHZ6.jpg |
Re: Vedo's TRX4 Shortened the wheelbase with the Incision 12.3in stainless link kit. Had to dremel off a bit of the rear drive shaft unfortunately https://i.imgur.com/leGpAV2.jpg Had to relocate the battery as well so i ordered a Hot Racing Battery relocation kit. https://i.imgur.com/bPJCR8g.jpg NOTE: it ain't cheap and make sure your LiPo's will fit between your body mounts before dropping 80 bucks CDN on it.:x https://i.imgur.com/LEBVDSL.jpg Not ideal but it works. https://i.imgur.com/LVnLe3x.jpg Quick solution to raise the rock sliders since the body sits high on the honcho cage... Nylon tubing. https://i.imgur.com/dKjXz3I.jpg |
Re: Vedo's TRX4 Finally got the body finished and the Samix brass in. Decided to ditch the Knight Customs grille for fittment reasons. So I cut a new body. FYI I had to remove the calipers off the Samix disc brakes becuse the Gmade NR-01's rubbed on them. https://i.imgur.com/QWNsdFm.jpg?1 https://i.imgur.com/GfExfQb.jpg?1 https://i.imgur.com/tfgHP0i.jpg?1 |
Re: Vedo's TRX4 This thing is almost unstoppable. Love this truck! https://i.imgur.com/klOxogI.jpg?1 https://i.imgur.com/FXwpj7J.jpg?1 |
Re: Vedo's TRX4 NICE "thumbsup" How’s the battery relocate kit work out? Too much weight up too high? |
Re: Vedo's TRX4 dude, that looks really awesome. You did a great job! |
Re: Vedo's TRX4 Quote:
Also, i'm sure it will be even less of an issue with a smaller battery. My 3s Hardcase is massive. |
Re: Vedo's TRX4 Quote:
|
Re: Vedo's TRX4 Wow, great use of the 4 runner body, it fits that chassis width and length perfectly. "thumbsup". Love the paint and chopped roof. |
Re: Vedo's TRX4 Very Nice! Love the TRX4 Sent from my iPhone using Tapatalk |
Re: Vedo's TRX4 Wow, almost not a TRX4 any longer. Looks great. |
All times are GMT -6. The time now is 06:28 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com