-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
NIRC. Chit Chat
- Thread starter sally1800
- Start date
Went to the woods today. After getting my Wraith all put together, I discovered 2 things wrong. Worn bearing in the tranny allowing the shaft to slop around, so I am ordering a new case and new bearings. Also the 2 Savox servos are drawing more then the BEC can provide, So I am going to step up to a 20A BEC and switch to a dig I think. It is ridiculous how hard it is to find damn parts for these things.
Anyway, here are some shots of the site by my house. We can run right out of the back of our cars here.
One entrance
Log Bridge
Anyway, here are some shots of the site by my house. We can run right out of the back of our cars here.
One entrance
Log Bridge
He ain't coming out here, he has made that clear. You guys are welcome anytime.
I got about 30 mins in today before I blew out the bearings in the tranny on the Wraith. Now I found a new case and all new bearings, the gears are all hardened steel as are the outputs. I tried to find a dig but no one has any. The Taco did great.
I got about 30 mins in today before I blew out the bearings in the tranny on the Wraith. Now I found a new case and all new bearings, the gears are all hardened steel as are the outputs. I tried to find a dig but no one has any. The Taco did great.
Come on guys that not nice. :roll:
On the good....
I like the rock section.
No this is funny (and sad). I was working on the Wraith today, putting together my tranny rebuild parts list and decided to look at my steering setup as is has been real slow. I was thinking that the 10A BEC wasn't enough. But as I dug in, I discovered that I had put a servo in the front that was supposed to run on 7.4VDC and at 6VDC it only had about 220 oz/in of torque, barely enough for a Hilux. So I am going to pull the rear steer, bump the BEC to 7.4 and move the rear steer which is 277 oz/in to my Hilux and the 168 oz/in fast one to the TT.
There is a lot of large rocks. I only walked the first couple hundred yards, plenty to do there till my tranny blew. I walked up on a bluff overlooking the ravine, probably 25 to 35 feet deep at that point and it goes on a ways. Some nice long climbs and some tough log sections that we can use as bridges.
I wouldn't buy 20 dollar bills at 10 bucks apiece from CKRC. I either buy locally (first choice) or RPP or Tower. Sometimes, on hard to find, Stormer has things that no one else has. When the world was out of over drive gear sets, they had them.
When you installed your dig, did you get the upgraded dig shaft or did you go with the stock dig setup?
i was hopin for thursday.. might be able to make friday work but might not.
CKRC?
the link I posted was Vanquish direct.
Same price as RPP Vanquish Products Hurtz Shifter Dig. They have it in stock as well
There is no upgraded dig shaft with the Vanquish Dig that I know of. Also if you buy direct from them I think it has a great warranty.
Only upgrades it trans gears
Robinson Racing Hardened Aluminum Diff Gear: AX10
Robinson Racing Hardened Aluminum Diff Gear: AX10
Robinson Racing Hard Steel Idler Gear AX10
Robinson Racing Hard Steel Idler Gear AX10
Oh ya you need a servo. Mine is set up to use a minny. When you get it watch out on the epa start low. 50
I only went on a small piece of it. Some mud but no water. The other end is. Ear a lake so may be some there
Axial's Wraith dig is $38.99, Vanquish's is $98.99. Go figure.
By the way, I have a set of black VP Wraith Chubs, black VP Wraith knuckles and home made drag link Nd steering link with the wraith steering plate for sale if anyone wants to try 4WS.
By the way, I have a set of black VP Wraith Chubs, black VP Wraith knuckles and home made drag link Nd steering link with the wraith steering plate for sale if anyone wants to try 4WS.
ill pick those up off ya.
I didn't know the Axial dig is out yet. I would post a wanted for a VP dig. I scored mine for $60 with a mini servo
Die-Laughing
RCC Addict
Who has some idea's on cool & innovative parts to machine? I'm looking to take on a project to get some custom parts on our rigs! What do you guys think?