How to: Make scale truck nutz

[zrider]

seen plenty of trucks with that and its hilarious haa might make some for my hauler

 

[obijuan]

You know, I dont know where you come from, but I have NEVER seen that on a truck before.

consider yourself, enlightened in a sense.

 

[Bird76Mojo]

Ya know, they actually outlawed these in certain states? Some governor was po'd over his kids seeing it or something? I remember hearing it in the news several months ago.

Careful guys!! :lol:

 

[Double J]

I made my Crawler ballz with ball bearings brazed togeather and a looped piece of speaker wire to allow movement.
Dipped them in Plasti-dip used a fingure cut from disposable latex gloves then dipped them in the plasti-dip again. (no need for sucking anything:lol: )

Let it dry and dip again.
If you wanted to you could sand down parts to make grooves and such (did it once) but usually comes out just right.

I used red cause that's what I had around. But the dip comes in Blue, Yellow, Black and red. I think I've seen a purple color but not sure.

 

[Bam Bam]

I did had a set on mine but they fell off at the gtg. They were the key nutz that truck nutz started to sell.

 

[west virginia krawler]

I made my Crawler ballz with ball bearings brazed togeather and a looped piece of speaker wire to allow movement.
Dipped them in Plasti-dip used a fingure cut from disposable latex gloves then dipped them in the plasti-dip again. (no need for sucking anything:lol: )

Let it dry and dip again.
If you wanted to you could sand down parts to make grooves and such (did it once) but usually comes out just right.

I used red cause that's what I had around. But the dip comes in Blue, Yellow, Black and red. I think I've seen a purple color but not sure.

Yea i tryed to make it sound not so perverted but o well. Hey where do u get the plastic dip from? Thanks

 

[Shaun]

slide the balls in the baloon. you know thats pretty sick dude.

 

[admiket]

gotta make a set. wike is going to hate them.

 

[Double J]

Yea i tryed to make it sound not so perverted but o well. Hey where do u get the plastic dip from? Thanks

I've found it at Lowes, Homo depot (they accused me of steeling so I don't like em), Harbor frieght, My local screw store (in red, black, blue and clear) and some all around type stores like wal-mart and K-mart in the tool section.

EDIT: I also noticed that if you mess with them to long before they dry the plasti-dip will eat through the laytex clove but not much. I was having a hard time getting the "shap" correct when I would hang it to dry and fiddled with it for about 5 minutes. Ended up taking the laytex off and putting a new one on. The thumb gives the best results.


EDIT-EDIT:
BADD's Ballz.:shock:

 

[NickRummy]

Reminds me of a picture I took of my truck a while back

 

[Derek Larsen]

Reminds me of a picture I took of my truck a while back

I know it's been a few years, but still, I would probably have that looked at by your healthcare provider.

 

[poop]

one is lower than the other ?

 

[caymin last]

one is lower than the other ?

You mean the IQ ? LOL!

 

[TURBOxN3RD]

These are my nuts.

Sent from my SCH-I545 using Tapatalk

 

[roksloski]

dude. thats so gross.

i so agree............



those on trucks are in such bad taste........


Maybe some of you have a small nut complex..........:shock::lmao:

 

[THX_138]

....

i so agree............



those on trucks are in such bad taste........


Maybe some of you have a small nut complex..........:shock::lmao:

 

[NitroDarwin]

I know I know this is an old thread but stumbled across these... https://www.ballsdeeptackle.com/collections/lead-sinkers I had a good laugh then thought of using them for this j/k

 

[xtreme4x2]

I just bought shaft and sack lures off ebay yesterday. Should be here in time for the salmon run mid august.

Also I once had a pair of the blue sacks on my bronco when I was in my early 20s

dragging them balls around :lmao:

 

[canadianbacon]

I mean, they're cool if your 12, or inbred I guess...